{"title":"Tonelux","description":null,"products":[{"product_id":"tonelux-mp1a-module","title":"Tonelux MP1A Module","description":"The \u003cb\u003eTonelux MP1a\u003c\/b\u003e is a DISCRETE mic preamp with a DIRECT INPUT on the front panel. The MIC IN is transformer coupled in and out, and has a 20 dB PAD switch (effects both MIC and DIR), a 48V Phantom switch and a Phase or POLARITY switch. The PAD and POLARITY switches effect both inputs. Identical to the MP1, but with the addition of an OUTPUT FADER to control the record level of the Mic Pre Output. The inner, or larger (silver) knob sets the mic pre gain and the outer smaller (black) knob controls the output level. We chose the fader control for the outer knob so the gain knob, once set, won't be bumped when adjusting the output level. \u003cbr\u003e\u003cbr\u003e The 8 seg LED VU meter follows the balanced output of the preamp. The level of the VU meter is adjustable over the entire range from off to +28. The PEAK led is set at +14VU or +18 dBu and can grab a fast peak and display it. With the \"a\" version, an internal jumper selects the MIC PRE MAIN OUTPUT or the MIC PRE GAIN STAGE signal to feed the VU Meter. This allows the engineer to monitor the real mic pre gain or the output level of the MP1a. When monitoring the Mic Pre Gain, the meter shows the actual gain stage level, and is not effected by the output fader. \u003cbr\u003e\u003cbr\u003e The Combo XLR\/Direct input is for use with a hi-z instrument, etc. The TILT tone control works with both the MIC in and DIR in and has it's own TILT EQ IN switch, which is a hard wire bypass switch when out. When turned up, the tilt control has a 0 to 6 dB boost on the high end while cutting the low end the same. If it is turned down, tilt will boost the low end up to 6 dB and cut the high end up to 6 dB. \u003cbr\u003e\u003cbr\u003e The Front panel XLR is multed to the rear panel XLR and that is also multed to the D-Sub \"INPUT\" on the rear of the V-Rack. The \"INSERT RETURN\" input of the V-Rack is a resistor isolated mic level input, that can be used when the MP1 is in a live recording situation and there is no splitter. It will bridge the mic line with 10X the impedance to minimize loading of the microphone. \u003cbr\u003e\u003cbr\u003e Included with the MP1a Mic Pre is the ability to PFL the output to an external amplifier or to the mixer\/master section for previewing the signal directly off the mic pre output.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449249493095,"sku":"4768","price":699.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mp1a_module.jpg?v=1787088308"},{"product_id":"tonelux-eq4p-module","title":"Tonelux EQ4P Module","description":"The \u003cb\u003eTonelux EQ4P\u003c\/b\u003e is a DISCRETE Parametric Equalizer with some very unique features. Notice that the panel has no Q control. The filter Q control is in relation to the Boost and Cut control, and uses a \"Constant Energy Curve\" that keeps the bandwidth wider at lower boost or cut levels and becomes narrow at higher boost or cut levels. This is musically pleasing. The curve is identical to many classic equalizers and is one of the reasons they are preferred over newer designs. When the PEAK button pressed, the 3 yellow \"peak\" buttons keep the width at a constant 1\/3 octave for more precision control. \u003cp\u003eThe High Frequency has a Shelving button instead of a Peak button. Since the Constant Energy Curve is so broad in the lower frequencies, there is no need for a low frequency shelf button. \u003c\/p\u003e\u003cp\u003eWith 4 bands of controls, each of the lower 2 have slightly different frequencies, allowing the lower band to go to 16 Hz, and the upper 2 bands are identical. The IN button is a silent IN\/OUT button that does not bypass the unit, but it bypasses the filters.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449252507751,"sku":"4770","price":699.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_eq4p_module.jpg?v=1787088321"},{"product_id":"tonelux-lfe-module","title":"Tonelux LFE Module","description":"Tonelux TX-LFE 80\/120 Hz Sub Woofer Filter","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449252868199,"sku":"6013","price":475.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_lfe_module.jpg?v=1787088323"},{"product_id":"tonelux-equalux-eq","title":"Tonelux Equalux Parametric EQ","description":"LAS VEGAS, NEVADA - SEPTEMBER 2008: Tonelux Designs Limited, distributed by TransAudio Group, is introducing their first product in an all new line of rack-mounted gear at the 125th AES Convention, in San Francisco, The single-rack space EQUALUX EQ is the equivalent of the highly sought after Tonelux EQ4P which fits into the Tonelux V-8 Roadster and Tonelux V-Rack. \u003cbr\u003e\u003cbr\u003e \u003cspan style=\"font-weight: bold;\"\u003eNoted Paul Wolff, president of Tonelux:\u003c\/span\u003e\u003cbr\u003e\"I have always felt that when creating a new product line in a different format than your standard line, the design must maintain the same quality as your existing products or even surpass them. If not, you are placing your entire brand in jeopardy. With the new Tonelux rack-mount modules, I have added features that didn't quite fit on the V-Rack module panel and, in addition, have incorporated valuable end user suggestions.\" \u003cbr\u003e\u003cbr\u003e The \u003cb\u003eTonelux EQUALUX\u003c\/b\u003e has all of the features of the EQ4P, plus proportional Q and fixed 1\/3 octave switches on ALL four bands, shelving on BOTH the high-frequency band and the low-frequency band, a silent IN\/OUT switch, and the addition of a hard wire bypass switch that also bypasses the unit in the unlikely event of a power failure. The front panel and chassis is a very sexy extrusion that will accent any rack of equipment. The EQUALUX EQs will be available after AES. In addition to the EQUALUX, Tonelux will be introducing the DYNALUX Compressor, a two-channel version of the TXC compressor, with many added linking and control features. A dual mic pre is also in the works.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449253720167,"sku":"10441","price":1499.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_equalux_eq.jpg?v=1787088327"},{"product_id":"tonelux-tilt","title":"Tonelux Tilt","description":"The famous Tonelux MP1A TILT EQ control in a 19” rack mount unit. The \u003cspan style=\"font-weight: bold;\"\u003eTonelux TILT\u003c\/span\u003e includes 8) TILT EQ controls with an IN\/OUT switch, and a POLARITY switch on each channel. Channels 1 and 2 have XLR inputs and outputs, and channels 1-8 also come out on D-SUBS. The input and outputs are fully balanced. \u003cbr\u003e \u003cbr\u003eA very inexpensive way to equalize 8 channels with a unique single knob control.The famous Tonelux MP1A TILT EQ control in a 19” rack mount unit. The TILT includes 8) TILT EQ controls with an IN\/OUT switch, and a POLARITY switch on each channel. Channels 1 and 2 have XLR inputs and outputs, and channels 1-8 also come out on D-SUBS. The input and outputs are fully balanced. A very inexpensive way to equalize 8 channels with a unique single knob control.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449254047847,"sku":"13053","price":999.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tilt.jpg?v=1787088328"},{"product_id":"tonelux-mx2d-module","title":"Tonelux MX2D Module","description":"The \u003cb\u003eTonelux MX2D Mixer\u003c\/b\u003e is a stereo line mixer with many features of a large frame console. The MX2 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare. The SOLO button is both a AFL or PFL, allowing both functions to be selected globally in the Control Room Section. \u003cp\u003eThe FADER knob is the channel fader, with the ability to insert an external fader from the rear panel. \u003c\/p\u003e\u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. \u003c\/p\u003e\u003cp\u003eThe INSERT button can act as a balanced insert for outboard equipment, or it can be used as a MIC PRE\/TAPE PLAY switch for live recording to check the mic pre output and then the output of the machine for confidence checks or post recording playback without repatching anything. \u003c\/p\u003e\u003cp\u003eThe ST button turns on the stereo bus, which allows the module to send to the aux sends without going to the stereo bus. \u003c\/p\u003e\u003cp\u003eThe Polarity switch is a standard phase inverter for the main signal path. \u003c\/p\u003e\u003cp\u003eThe 4 sends are internally configurable for PRE or POST fader signal. The MX2 has an optional DIRECT transformer output.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449266663527,"sku":"4772","price":495.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mx2d_module.jpg?v=1787088372"},{"product_id":"tonelux-mx5-1d-module","title":"Tonelux MX5.1D Module","description":"The \u003cb\u003eTonelux MX5.1 Mixer\u003c\/b\u003e is a SURROUND line mixer with many features of a large frame console. The MX5.1 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare, etc. The SOLO button is both a AFL or PFL, allowing both functions to be selected globally in the Control Room Section. \u003cp\u003eThe FADER knob is the channel fader, with the ability to insert an external fader from the rear panel. \u003c\/p\u003e\u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. \u003c\/p\u003e\u003cp\u003eThe INSERT button can act as a balanced insert for outboard equipment, or it can be used as a MIC PRE\/TAPE PLAY switch for live recording to check the mic pre output and then the output of the machine for confidence checks or post recording playback without repatching anything. \u003c\/p\u003e\u003cp\u003eThe Polarity switch is a standard phase inverter for the main signal path. \u003c\/p\u003e\u003cp\u003eThe 5.1 switch turns on the signal to the surround bus, allowing the module to send signal to the aux sends without going to the surround bus. \u003c\/p\u003e\u003cp\u003eThe LCR button switches the PAN pot from stereo to LCR, and pans from left, through center, to right, or in 2 channel stereo, allowing phantom center. \u003c\/p\u003e\u003cp\u003eThe 2 sends are internally configurable for PRE or POST fader signal. One of the sends can be used as the LFE send for Surround Mixes. \u003c\/p\u003e\u003cp\u003eThe MX5.1 has an optional DIRECT transformer output.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449266696295,"sku":"4773","price":585.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mx5.1d_module.jpg?v=1787088372"},{"product_id":"tonelux-mx5-1-module","title":"Tonelux MX5.1 Module","description":"The \u003cb\u003eTonelux MX5.1 Mixer\u003c\/b\u003e is a SURROUND line mixer with many features of a large frame console. The MX5.1 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare, etc. The SOLO button is both a AFL or PFL, allowing both functions to be selected globally in the Control Room Section. \u003cp\u003eThe FADER knob is the channel fader, with the ability to insert an external fader from the rear panel. \u003c\/p\u003e\u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. \u003c\/p\u003e\u003cp\u003eThe INSERT button can act as a balanced insert for outboard equipment, or it can be used as a MIC PRE\/TAPE PLAY switch for live recording to check the mic pre output and then the output of the machine for confidence checks or post recording playback without repatching anything. \u003c\/p\u003e\u003cp\u003eThe Polarity switch is a standard phase inverter for the main signal path. \u003c\/p\u003e\u003cp\u003eThe 5.1 switch turns on the signal to the surround bus, allowing the module to send signal to the aux sends without going to the surround bus. \u003c\/p\u003e\u003cp\u003eThe LCR button switches the PAN pot from stereo to LCR, and pans from left, through center, to right, or in 2 channel stereo, allowing phantom center. \u003c\/p\u003e\u003cp\u003eThe 2 sends are internally configurable for PRE or POST fader signal. One of the sends can be used as the LFE send for Surround Mixes. \u003c\/p\u003e\u003cp\u003eThe MX5.1 has an optional DIRECT transformer output.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449266729063,"sku":"4774","price":485.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mx5.1_module.jpg?v=1787088372"},{"product_id":"tonelux-fx2-module","title":"Tonelux FX2 Module","description":"The \u003cb\u003eTonelux FX2\u003c\/b\u003e Mixer is a DUAL stereo line mixer with a simple pair of level controls and a pair of panners. \u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. The FX2 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare. \u003c\/p\u003e\u003cp\u003eThe \u003cb\u003eFX2+ \"AUX MSTR\" \u003c\/b\u003eis an OPTIONAL send master, which can be used in place of the SM1 or SM2 bus master when rack space is critical. It allows the rack to be filled with a full set of 16 modules, giving you 32 channels, including the masters, ALL IN ONE 3U RACK. \u003c\/p\u003e\u003cp\u003eThe rear panel feature connector provides for an external fader for the send master option on the FX2+. \u003c\/p\u003e\u003cp\u003eThe FX2 can be used by it self as a inexpensive dual stereo mixer for DAW or LIVE use when a simple stereo bus is all that is required. \u003c\/p\u003e\u003cp\u003eWhen used with the MX2 series, the addition of FOUR FX2 modules will give you 8 returns and the masters for the FOUR sends on the MX2, saving you the space of having FOUR SM1 master modules. \u003c\/p\u003e\u003cp\u003eThe FX2 can also be used as an additional set of sends, fed from the direct output of the MX2, as the outputs of each panner can be internally set to feed any of the 16 available busses in the VRACK, allowing up to EIGHT sends from each MX2, including the onboard set of FOUR sends. \u003c\/p\u003e\u003cp\u003eThis module, when used as a simple external summing module, will bring the cost of a DAW external mixing system down considerably.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449266761831,"sku":"4775","price":425.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_fx2_module.jpg?v=1787088372"},{"product_id":"tonelux-fx2-module-1","title":"Tonelux FX2+ Module","description":"The \u003cb\u003eTonelux FX2+ Mixer\u003c\/b\u003e is a DUAL stereo line mixer with a simple pair of level controls and a pair of panners. \u003cbr\u003e \u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. The FX2 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare. \u003c\/p\u003e\u003cp\u003eThe \u003cb\u003eFX2+ \"AUX MSTR\" \u003c\/b\u003eis an OPTIONAL send master, which can be used in place of the SM1 or SM2 bus master when rack space is critical. It allows the rack to be filled with a full set of 16 modules, giving you 32 channels, including the masters, ALL IN ONE 3U RACK. \u003c\/p\u003e\u003cp\u003eThe rear panel feature connector provides for an external fader for the send master option on the FX2+. \u003c\/p\u003e\u003cp\u003eThe FX2 can be used by it self as a inexpensive dual stereo mixer for DAW or LIVE use when a simple stereo bus is all that is required. \u003c\/p\u003e\u003cp\u003eWhen used with the MX2 series, the addition of FOUR FX2 modules will give you 8 returns and the masters for the FOUR sends on the MX2, saving you the space of having FOUR SM1 master modules. \u003c\/p\u003e\u003cp\u003eThe FX2 can also be used as an additional set of sends, fed from the direct output of the MX2, as the outputs of each panner can be internally set to feed any of the 16 available busses in the VRACK, allowing up to EIGHT sends from each MX2, including the onboard set of FOUR sends. \u003c\/p\u003e\u003cp\u003eThis module, when used as a simple external summing module, will bring the cost of a DAW external mixing system down considerably.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449266794599,"sku":"4776","price":495.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_fx2__module.jpg?v=1787088372"},{"product_id":"tonelux-aux1-buss-access-module","title":"Tonelux AUX1 Buss Access Module","description":"The \u003cb\u003eTonelux AUX1 \u003c\/b\u003eis a simple BUS access module that allows the user to insert an additional mixer, mic pre, etc. into the Tonelux MIX BUS. Each input is BALANCED and is calibrated for a level of +4 dBu \u003cp\u003e The LED at the bottom of the module indicates the mode that the AUX1 is in. Internally, there are headers that allow you to switch the jacks from the MX2 Stereo Mixer's busses to the MX5.1 Surround Mixer's busses, since any combination of modules can be used at the same time in the rack.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449267810407,"sku":"4777","price":325.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_aux1_buss_access_module.jpg?v=1787088372"},{"product_id":"tonelux-v-rack","title":"Tonelux V-Rack","description":"The \u003cb\u003eTonelux V-RACK\u003c\/b\u003e accommodates 16 Tonelux Modules in any combination.\u003cbr\u003e\u003cbr\u003e\u003cul\u003e\n\u003cli\u003e16 spaces (D-Sub in\/out)\u003c\/li\u003e\n\u003cli\u003e3U high\u003c\/li\u003e\n\u003cli\u003e2 V Racks per PSU\u003c\/li\u003e\n\u003cli\u003eV Rack is the core building block of Tonelux consoles.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449267843175,"sku":"4778","price":499.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_v-rack.jpg?v=1787088373"},{"product_id":"tonelux-sm1-module","title":"Tonelux SM1 Module","description":"The \u003cb\u003eTonelux SM1\u003c\/b\u003e is a DISCRETE Mono Summing module, with a selectable input (on the PC board with jumpers) so you can grab any bus and use the SM1 as the summing master for the bus, such as Sends, Center Channel, LFE, PFL, etc. \u003cp\u003e The 8 seg LED VU meter follows the output of the final stage. The Summing input uses the Tonelux DISCRETE op-amp for summing, then feeds the Tonelux DISCRETE output op-amp into a transformer for the summing (or ACA) output. The return from the ACA out comes back into a DISCRETE booster amp, the master fader and transformer for the final output stage. \u003c\/p\u003e\u003cp\u003e This configuration allows you to insert a compressor after the summing amp and before the master fader (either the front panel pot or the external fader option), then returning it back into the fader and to the final Booster output. This modules works the same way any typical professional recording console would work. \u003c\/p\u003e\u003cp\u003e The INS (insert) button allows the engineer to compare or insert the device such as a compressor for IN\/OUT comparison or when required for a special CUE point. \u003c\/p\u003e\u003cp\u003e The SM1 is also available with only a Summing\/Booster\/Fader output when the INS function is not required, as when it is used for a send master. \u003c\/p\u003e\u003cp\u003e Both the ACA output and the BOOSTER output are transformer coupled.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449267875943,"sku":"4783","price":495.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_sm1_module.jpg?v=1787088373"},{"product_id":"tonelux-sm2-module","title":"Tonelux SM2 Module","description":"The \u003cb\u003eTonelux SM2\u003c\/b\u003e is a STEREO DISCRETE Summing module, with selectable inputs (on the PC board with jumpers) so you can grab any pair of bus and use the SM2 as the summing master for the Stereo bus, Surround Bus or the Solo Bus, etc. \u003cp\u003e The two 8 seg LED VU meters follows the outputs of the both final stages. The Summing inputs use the Tonelux DISCRETE op-amp for summing, then feeds the Tonelux DISCRETE output op-amp into a transformer for the summing (or ACA) outputs. The return from the ACA out comes back into a DISCRETE booster amp, the master fader and transformer for the final output stages. \u003c\/p\u003e\u003cp\u003e This configuration allows you to insert a Stereo compressor after the summing amp and before the master fader (either the front panel pot or the external fader option), then returning it back into the fader and to the final Booster outputs. This modules works the same way any typical professional recording console would work. \u003c\/p\u003e\u003cp\u003e The INS (insert) button allows the engineer to compare or insert the device such as a compressor for IN\/OUT comparison or when required for a special CUE point. One switch controls both channels. \u003c\/p\u003e\u003cp\u003e The rear panel connector allows the user to insert a Stereo fader, which will serve as the Master fader. \u003c\/p\u003e\u003cp\u003e Both the ACA outputs and the BOOSTER outputs are transformer coupled.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449267941479,"sku":"4784","price":895.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_sm2_module.jpg?v=1787088373"},{"product_id":"tonelux-fd1-fader-module","title":"Tonelux FD1 Fader Module","description":"The \u003cb\u003eTonelux FD1 Fader \u003c\/b\u003eis a mono 100mm fader. The price includes a 2 foot TRS cable that plugs into the rear of the MX2, MX5.2 or the SM1, SM2 as well as the FX2 external fader jack on the rear of the VRACK.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449267908711,"sku":"4785","price":225.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_fd1_fader_module.jpg?v=1787088373"},{"product_id":"tonelux-fd2-stereo-fader-module","title":"Tonelux FD2 Stereo Fader Module","description":"FD2 Stereo 100mm Fader w\/Hookup Cable","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449268695143,"sku":"4786","price":275.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_fd2_stereo_fader_module.jpg?v=1787088373"},{"product_id":"tonelux-psu","title":"Tonelux PSU","description":"Powers up to 2 rack units.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449268760679,"sku":"4787","price":599.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_psu.jpg?v=1787088373"},{"product_id":"tonelux-cr2-module","title":"Tonelux CR2 Module","description":"The \u003cb\u003eTonelux CR2\u003c\/b\u003e is a FULL featured CONTROL ROOM MONITOR module that has Three External Stereo Inputs and the internal Stereo Mix Bus. The CR2 uses an ALL DISCRETE signal path for superb sonic quality. \u003cp\u003eThe features include AFL stereo level, which is switched on when ever a channel is soloed, TWO control room speaker outputs, a MONO compatibility switch, Left and Right Speaker CUT switches and a DIM control that dims the Control room level 15dB. \u003c\/p\u003e\u003cp\u003eThe CONTROL ROOM LEVEL pot is a matched detented stereo control for perfect imaging. Of course, it uses a HUGE Tonelux knob! \u003c\/p\u003e\u003cp\u003eThere is a talkback feature that when pressed, sends an external mic signal into the send busses via the COM button. This also automatically DIMs the Control Room Level. \u003c\/p\u003e\u003cp\u003eThe two 8 seg VU meters follow the selection of the Control Room and are also accessible from the rear of the VRACK for an external set of VU meters.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449268858983,"sku":"4949","price":895.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_cr2_module.jpg?v=1787088374"},{"product_id":"tonelux-universal-console","title":"Tonelux Universal Console","description":"The \u003cb\u003eTonelux Universal Console \u003c\/b\u003ecan be configured for up to 96 channels, room for Eqs, Mic Pres, Compressors, Control Room Section, Returns, Masters, and the new ShadowMix Motorized Fader System that uses your DAW's automation to run them, but with the audio going through them into the Tonelux modules!!! \u003cbr\u003e\u003cbr\u003eTonelux provides a system that can do tracking, mixing, overdubs and most other production work with the broad line of modular products it manufactures. We have taken many of the oversimplified external systems and included many of the large format console features into a very high quality, affordable system of modules that can be combined or used individually. We have used both discrete and IC based amplifiers in the positions that they each work the best in. With two new discrete opamps, the Tonelux line sounds as sweet as possible, with most comments referring to it's \"dimensional sound\" and it's \"clear high end and fat bottom\". \u003cbr\u003e\u003cbr\u003eThe starting point is the flexible Tonelux multi-function powered rack. With one single rack model, you can intermix any of the modules in any quantity because the configuration of the rack is universal for all modules. With Paul Wolff's extensive experience with console designs, beginning with his many years spent customizing live sound consoles, studio consoles and working in both environments, building nearly 35 custom consoles, through his final design of the first discrete surround console, not forgetting the modular designs of some of the first OTB summing mixers, EQs, Mic Pres and Compressors that are still being sold as they were designed, Tonelux was the next logical step, quickly becoming the leader in modular, configurable production systems, with a complete ground up concept that doesn't use obsolete designs to make something that appears new. \"With a dramatic new direction in the music industry, the way everything is done is being re-invented, and that requires a new direction in the way we design our tools.\" \u003cbr\u003e\u003cbr\u003e\"I started to see a change in the industry, and saw a need for a system that enhanced the way engineers, producers and musicians recorded their music. The DAW is here to stay, which many people and companies still regard as the 'studio killer'. Like any new invention, the DAW has changed the face of recording for ever, and with change, comes new opportunities, not always seen at first.\" It's like either being on the train or being on the tracks... \u003cbr\u003e\u003cbr\u003e\u003chr\u003e\u003ch3\u003eWe've been buying, selling and restoring the world’s best consoles since 1993\u003c\/h3\u003e\u003cp\u003eShopping for a recording console can be an intimidating process. You can spend countless hours online searching for answers only to end up with more questions than when you started. That's why we’ve created our one-of-a-kind shopping experience to help you purchase the console that is exactly right for you and your studio.\u003c\/p\u003e\u003cp\u003eFinding the perfect console means being connected, and for over 20 years, we’ve been one of the biggest players in the worldwide audio marketplace. We’ve helped thousands of customers complete the console buying process, while also helping to facilitate brokered sales, gear trade-ins and purchasing classic desks for refurbishment.\u003c\/p\u003e\u003cp\u003eEach of our premium serviced consoles has passed through a rigorous multi-point inspection and meticulous testing to ensure the result is a world-class restoration. Upon completion, your console will be expertly crated and shipped to your studio, where our highly skilled technical experts can lead a worry-free integration.\u003c\/p\u003e\u003cp\u003eNo matter whether you’re interested in a vintage piece or the latest releases, our team of experts can answer even the toughest questions. From servicing and shipping consoles to creating custom furniture, patch bays and turnkey packages, we’ve been involved in every aspect of the industry. We work tirelessly to provide the best selection, service and support anywhere to help our customers find the console of their dreams. Want to see what we can do for you? Talk to one of our console experts by calling \u003ca href=\"tel:8886531184\"\u003e888.653.1184\u003c\/a\u003e or you can \u003ca href=\"\/contacts\"\u003eemail us\u003c\/a\u003e.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274364007,"sku":"5978","price":0.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_universal_console.jpg?v=1787088396"},{"product_id":"tonelux-mx2-module","title":"Tonelux MX2 Module","description":"The \u003cb\u003eTonelux MX2 Mixer\u003c\/b\u003e is a stereo line mixer with many features of a large frame console. The MX2 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare. The SOLO button is both a AFL or PFL, allowing both functions to be selected globally in the Control Room Section. \u003cp\u003eThe FADER knob is the channel fader, with the ability to insert an external fader from the rear panel. \u003c\/p\u003e\u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. \u003c\/p\u003e\u003cp\u003eThe INSERT button can act as a balanced insert for outboard equipment, or it can be used as a MIC PRE\/TAPE PLAY switch for live recording to check the mic pre output and then the output of the machine for confidence checks or post recording playback without repatching anything. \u003c\/p\u003e\u003cp\u003eThe ST button turns on the stereo bus, which allows the module to send to the aux sends without going to the stereo bus. \u003c\/p\u003e\u003cp\u003eThe Polarity switch is a standard phase inverter for the main signal path. \u003c\/p\u003e\u003cp\u003eThe 4 sends are internally configurable for PRE or POST fader signal. The MX2 has an optional DIRECT transformer output.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274429543,"sku":"6003","price":435.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mx2_module.jpg?v=1787088397"},{"product_id":"tonelux-tb1-module","title":"Tonelux TB1 Module","description":"Cue\/Talk Back Module","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274462311,"sku":"6007","price":475.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tb1_module.jpg?v=1787088397"},{"product_id":"tonelux-f-rack","title":"Tonelux F-Rack","description":"The \u003cb\u003eTonelux TX-FRACK\u003c\/b\u003e accommodates 16 Modules in any combination.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274495079,"sku":"6008","price":265.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_f_rack.jpg?v=1787088397"},{"product_id":"tonelux-tr8-module","title":"Tonelux TR8 Module","description":"The \u003cb\u003eTonelux TR8 Bus Assign Module\u003c\/b\u003e is a mono input line level module with a simple level control and a panner. \u003cbr\u003e\u003cbr\u003e The PAN control is a standard stereo pan circuit with a center detent. \u003cbr\u003e\u003cbr\u003e The TR8 uses the proprietary all discrete TX-240 op-amp and with the TR8+ bus master option, the all discrete TX-260 output stage with the TX-280 transformer.\u003cbr\u003e\u003cbr\u003e The TR8+ \"BUS MSTR\" is an OPTIONAL bus master control, which is used for controlling the levels of the busses, or can be assigned to any of the busses for a simple Stereo master, Aux master or Surround bus master. It can also serve as the replacement for the SM1 or SM2 bus master. \u003cbr\u003e\u003cbr\u003e It allows the rack to be filled with a full set of 16 modules, giving you 16 in X 8 out channels, including the masters, ALL IN ONE 3U RACK. \u003cbr\u003e\u003cbr\u003e The rear panel feature connector provides for an external fader for the bus master option on the TR8+. \u003cbr\u003e\u003cbr\u003e The TR8 can be used by it self as a inexpensive mono in, 8 out mixer for DAW or LIVE use when a flexable module is required with multiple outputs. It can serve as a monitor matrix, additional sends or even a Mix Minus matrix for live. This module, when used as a simple external summing module, will bring the cost of a DAW external mixing system down considerably while allowing panning between any pair of busses, which could be assigned to the Stereo Bus and the Surround busses. \u003cbr\u003e\u003cbr\u003e When used with the MX2 series, the addition of FOUR more TR8+ modules will give you the masters for the FOUR sends on the MX2, saving you the space of having FOUR SM1 master modules, with the added feature of routing when tracking or more inputs when mixing. \u003cbr\u003e\u003cbr\u003e The TR8 can also be used as an additional set of 8 sends, fed from the direct output of the MX2, as the outputs of any of the bus switches can be internally set to feed any of the 16 available busses in the VRACK, allowing up to EIGHT additional sends from each MX2.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274560615,"sku":"6009","price":425.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tr8_module.jpg?v=1787088397"},{"product_id":"tonelux-tr8-module-1","title":"Tonelux TR8+ Module","description":"The \u003cb\u003eTonelux TR8 Bus Assign Module\u003c\/b\u003e is a mono input line level module with a simple level control and a panner. \u003cbr\u003e\u003cbr\u003e The PAN control is a standard stereo pan circuit with a center detent. \u003cbr\u003e\u003cbr\u003e The TR8 uses the proprietary all discrete TX-240 op-amp and with the TR8+ bus master option, the all discrete TX-260 output stage with the TX-280 transformer.\u003cbr\u003e\u003cbr\u003e The TR8+ \"BUS MSTR\" is an OPTIONAL bus master control, which is used for controlling the levels of the busses, or can be assigned to any of the busses for a simple Stereo master, Aux master or Surround bus master. It can also serve as the replacement for the SM1 or SM2 bus master. \u003cbr\u003e\u003cbr\u003e It allows the rack to be filled with a full set of 16 modules, giving you 16 in X 8 out channels, including the masters, ALL IN ONE 3U RACK. \u003cbr\u003e\u003cbr\u003e The rear panel feature connector provides for an external fader for the bus master option on the TR8+. \u003cbr\u003e\u003cbr\u003e The TR8 can be used by it self as a inexpensive mono in, 8 out mixer for DAW or LIVE use when a flexable module is required with multiple outputs. It can serve as a monitor matrix, additional sends or even a Mix Minus matrix for live. This module, when used as a simple external summing module, will bring the cost of a DAW external mixing system down considerably while allowing panning between any pair of busses, which could be assigned to the Stereo Bus and the Surround busses. \u003cbr\u003e\u003cbr\u003e When used with the MX2 series, the addition of FOUR more TR8+ modules will give you the masters for the FOUR sends on the MX2, saving you the space of having FOUR SM1 master modules, with the added feature of routing when tracking or more inputs when mixing. \u003cbr\u003e\u003cbr\u003e The TR8 can also be used as an additional set of 8 sends, fed from the direct output of the MX2, as the outputs of any of the bus switches can be internally set to feed any of the 16 available busses in the VRACK, allowing up to EIGHT additional sends from each MX2.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274593383,"sku":"6010","price":495.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tr8__module.jpg?v=1787088397"},{"product_id":"tonelux-blank-panel","title":"Tonelux Blank Panel","description":"Blank Tonelux Panel","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449274626151,"sku":"6011","price":29.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_blank_panel.jpg?v=1787088397"},{"product_id":"tonelux-txc-module","title":"Tonelux TXC Module","description":"The \u003cb\u003eTonelux TXC \u003c\/b\u003eis the new design from Paul Wolff that addresses the complex issues with compression. \u003cbr\u003e\u003cbr\u003e With the ability to do in-module parallel mixing of the dry signal and the compressed signal, the engineer can now enjoy the parallel or \"side chaining\" of an instrument with itself and come up with the perfect blend of the original and compressed signal without the problems associated with in-the-box latency. \u003cbr\u003e\u003cbr\u003e The TXC uses the proprietary all discrete TX-240 op-amp and the all discrete TX-260 output stage with the TX-280 transformer. \u003cbr\u003e\u003cbr\u003e In addition to the Input\/Compressor MIX knob, the TXC has many other unique features not found on any compressor made today. The ability of being able to switch between Feed Back and Feed Forward compression is something that is not new to Paul Wolff. With the TXC, he decided to take it one step further by allowing the ability to fade between Feed Back compression and Feed Forward compression with the TYPE control. This feature gives the engineer the freedom to combine the smooth nature of the Feed Back type of compression with the agressive effect of Feed Forward compression. \u003cbr\u003e\u003cbr\u003e In addition to the FB-FF Type control, the TXC has the ability to over compress with the RATIO control, which allows compression ratios from 1.5:1 to 20:1, and then beyond, with the \"OVER:\" ratio settings that cause the compressor to reduce the gain at a higher ratio than the gain is going into it. This means that the ratio control allows the compressor to compress an increase in signal of 10dB with a gain reduction of up to -8dB. If the signal goes up 10dB, the output will go DOWN 8dB. \u003cbr\u003e\u003cbr\u003e This becomes useful when taking a pre compressed snare and by adjusting the Attack, and setting the Ratio in the OVER: area, you can actually recover the initial impact peak of the snare. This, with the MIX control, can then be blended back with the original \"flat\" snare and you now have a dynamic snare again, but with a very controlled peak. \u003cbr\u003e\u003cbr\u003e The TXC also inserted the now famous \"TILT\" control into the side chain of the RMS detector, so you can increase the highs and decrease the lows going into the RMS detector, virtually eliminating the effects of pumping because the Detector is seeing a more uniform distribution of energy across the spectrum instead of a bass heavy signal like most compressors. \u003cbr\u003e\u003cbr\u003e The Attack control has a X5 switch to allow for a range of extremely fast attack (in the micro second range) all the way through a very smooth slow attack, more suited for leveling. \u003cbr\u003e\u003cbr\u003e The Release control can be almost instantaneous to 3 seconds. The release circuit is a unique 3 stage circuit that auto releases the faster signals at a rate of 10 times the release of the lower frequency signals. All of this and an auto-makeup gain system that always keeps the gain at unity regardless of the amount of compression. \u003cbr\u003e\u003cbr\u003e With a 6 LED Gain Reduction meter and an adjustable link control, the TXC can be used in mono or stereo configurations with ease.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449295269991,"sku":"8099","price":699.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_txc.jpg?v=1787088448"},{"product_id":"tonelux-cr-adapter-kit","title":"Tonelux CR Adapter Kit","description":"This adapter goes on back of V rack for easier hookup of TL cabling. When using this card, you MUST place these modules on the left or right half of your Vrack in either order: FX2 (FX2+)x4, SM2, CR2 or CR2, SM2 and FX2 )FX2+)x4. \u003cbr\u003e\u003cbr\u003e You need to have a minimum of these above modules to make use of this card. As per Paul\/Tonelux, the use of this board saves approximately one day of labor, as opposed to hand wiring a system without the use of the board. 4x dsub to dsub ribbon jumpers are required connect this card to the V rack. A maximum of 3 feet in length is recommended. The card can be mounted to the NEW STYLE V racks that are now being shipped tie bars, or the card can be mounted remotely. The card has optional surface mounted XLR outputs that can be added.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449295990887,"sku":"8288","price":140.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_cr_adapter_kit.jpg?v=1787088451"},{"product_id":"tonelux-8-channel-v8-roadster-unloaded","title":"Tonelux 8 Channel V8 Roadster - Unloaded","description":"The \u003cspan style=\"font-weight: bold;\"\u003eTonelux V8 Roadster\u003c\/span\u003e can be custom-loaded with any one of 20 different Tonelux Custom Console Modules to create any portable rig you can envision. D-sub and XLR ins \u0026amp; outs make this a snap to quickly connect\/disconnect in the studio. Expand later with a V-Rack and\/or a Tonelux full blown frame console!\u003cbr\u003e\u003cbr\u003eThe\u003cspan style=\"font-weight: bold;\"\u003e \u003c\/span\u003eV8\u003cb\u003e \u003c\/b\u003eincludes many features not found on any other rack system available today. \u003cbr\u003e\u003cbr\u003e The rack can house up to 8x Mic Pres, Eqs and Compressors, in any combination. \u003cbr\u003e\u003cbr\u003e The rack can also house any of the MIXING modules, including the MX2, FX2, MX5.1, SM2, TR8, and the CR2 for monitoring. \u003cbr\u003e\u003cbr\u003e The system pictured above is an 8) channel mixer with 2) MP1A Mic Pres and 2) EQ4P Equalizers. \u003cbr\u003e\u003cbr\u003e Having a Vrack back at the studio filled with MX2s and a CR2 module can link to the portable rack which allow both racks become one large system! \u003cbr\u003e\u003cbr\u003e \u003cb\u003eThese features include:\u003c\/b\u003e\u003cul\u003e \u003cli\u003e8x Module Slots \u003c\/li\u003e\n\u003cli\u003eXLR inputs and outputs for the Input, Insert Return\/Side Chain, and Output \u003c\/li\u003e\n\u003cli\u003eD-SUB inputs and outputs for the Input, Insert Return\/Side Chain, and Output \u003c\/li\u003e\n\u003cli\u003eD-Sub BUS linking to the VRack System to expand bussing, etc. \u003c\/li\u003e\n\u003cli\u003eLarge Power Supply, can power an additional VRack Aux power connector on rear. \u003c\/li\u003e\n\u003cli\u003eFolding Handle \u003c\/li\u003e\n\u003cli\u003eRubber feet on side and bottom \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449299333223,"sku":"8837","price":749.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_8_channel_v8_roadster_unloaded.jpg?v=1787088458"},{"product_id":"tonelux-x-rack","title":"Tonelux X-Rack","description":"The \u003cb\u003eTonelux X-RACK\u003c\/b\u003e accommodates 8 Tonelux Modules in any combination.\u003cbr\u003e\u003cbr\u003e\u003cul\u003e\n\u003cli\u003e8 Module ½ Rack\u003c\/li\u003e\n\u003cli\u003e8 spaces\u003c\/li\u003e\n\u003cli\u003e1 spare Fader space\u003c\/li\u003e\n\u003cli\u003eXLR and D-Sub in\/out\u003c\/li\u003e\n\u003cli\u003e3U high \u003c\/li\u003e\n\u003cli\u003e4 X Racks per PSU\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449308737639,"sku":"11161","price":499.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_x-rack.jpg?v=1787088497"},{"product_id":"tonelux-v4-500-series-rack","title":"Tonelux V4 Roadster 500 Series Rack - Unloaded","description":"\u003cspan style=\"font-weight: bold;\"\u003eTonelux V4 Portable 500 Series Rack\u003c\/span\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e\nSelf-powered\u003c\/li\u003e\n\u003cli\u003eCan power eight modules plus a V-Rack\u003c\/li\u003e\n\u003cli\u003e\nInternational Universal Power Supply\u003c\/li\u003e\n\u003cli\u003e\nXLR inputs and outputs\u003c\/li\u003e\n\u003cli\u003e\nAll steel design, very rugged\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449349795943,"sku":"16947","price":299.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_v4_rack.jpg?v=1787088657"},{"product_id":"tonelux-vu4-vu-meter","title":"Tonelux VU4 VU Meter","description":"The \u003cb\u003eTonelux model VU4\u003c\/b\u003e metering module allows inserting a metering system between any signal in the Tonelux modular setup. The VU4 will not load the signal significantly, as it has an input impedance of over 100K. With the ability to accept two separate signals from two sources, the VU4 can be used as a “Source\/Tape” metering system with external control over the switching of all meters.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449350123623,"sku":"7656","price":585.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_vu4_vu_meter.jpg?v=1787088658"},{"product_id":"tonelux-model-1628-console","title":"Tonelux Model 1628 Console","description":"From the mind of Paul Wolff comes the Model 1628, the first Discrete plug and play console for the Tonelux product line. \u003cbr\u003e\u003cbr\u003eThe 1628 includes a professional 192 point TT patchbay and I\/O panel as standard and can be expanded with any combination of Vracks, the 8 channel or 16 channel expanders.\u003cbr\u003e \u003cbr\u003e Features\u003cbr\u003e \u003cul\u003e\n\u003cli\u003e16x MX2 Mix Modules\u003c\/li\u003e\n\u003cli\u003e16x EQ4P Equalizers\u003c\/li\u003e\n\u003cli\u003e16x TR8 Bus Assign Modules\u003c\/li\u003e\n\u003cli\u003e16x MP1a Mic Preamps with TILT\u003c\/li\u003e\n\u003cli\u003e4x FX2+ Send Master\/FX Returns\u003c\/li\u003e\n\u003cli\u003e1x SM2 Stereo Master Module\u003c\/li\u003e\n\u003cli\u003e1x CR2 Control Room Module\u003c\/li\u003e\n\u003cli\u003e1x TB1 TalkBack Module\u003c\/li\u003e\n\u003cli\u003e16x P\u0026amp;G Custom Manual Fadersz\u003c\/li\u003e\n\u003cli\u003e16x VU Meters in a Removable Bridge\u003c\/li\u003e\n\u003cli\u003e2x Stereo VU Meters\u003c\/li\u003e\n\u003cli\u003eCustom Designed Wood Sides\/Top\u003c\/li\u003e\n\u003cli\u003eLeather Bolster\u003c\/li\u003e\n\u003cli\u003eComplete TT Patchbay\/DSub I\/O Panel\u003c\/li\u003e\n\u003cli\u003eOptional ShadowMix Automation\u003c\/li\u003e\n\u003c\/ul\u003e \u003cbr\u003e\u003cbr\u003e\u003chr\u003e\u003ch3\u003eWe've been buying, selling and restoring the world’s best consoles since 1993\u003c\/h3\u003e\u003cp\u003eShopping for a recording console can be an intimidating process. You can spend countless hours online searching for answers only to end up with more questions than when you started. That's why we’ve created our one-of-a-kind shopping experience to help you purchase the console that is exactly right for you and your studio.\u003c\/p\u003e\u003cp\u003eFinding the perfect console means being connected, and for over 20 years, we’ve been one of the biggest players in the worldwide audio marketplace. We’ve helped thousands of customers complete the console buying process, while also helping to facilitate brokered sales, gear trade-ins and purchasing classic desks for refurbishment.\u003c\/p\u003e\u003cp\u003eEach of our premium serviced consoles has passed through a rigorous multi-point inspection and meticulous testing to ensure the result is a world-class restoration. Upon completion, your console will be expertly crated and shipped to your studio, where our highly skilled technical experts can lead a worry-free integration.\u003c\/p\u003e\u003cp\u003eNo matter whether you’re interested in a vintage piece or the latest releases, our team of experts can answer even the toughest questions. From servicing and shipping consoles to creating custom furniture, patch bays and turnkey packages, we’ve been involved in every aspect of the industry. We work tirelessly to provide the best selection, service and support anywhere to help our customers find the console of their dreams. Want to see what we can do for you? Talk to one of our console experts by calling \u003ca href=\"tel:8886531184\"\u003e888.653.1184\u003c\/a\u003e or you can \u003ca href=\"\/contacts\"\u003eemail us\u003c\/a\u003e.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449351696487,"sku":"16435","price":53999.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_model_1628_1.jpg?v=1787088664"},{"product_id":"tonelux-shadowmix-fader-automation","title":"Tonelux ShadowMix Fader Automation","description":"The \u003cb\u003eTonelux ShadowMix(tm)\u003c\/b\u003e Automation package uses the DAW for the automation. Includes local mute and solo in place.\u003cbr\u003e\u003cbr\u003e It can be controlled from AVID’s Media Composer, Film Composer and Xpress, Digidesign’s Pro Tools, and most computer based MIDI software including programs from Cakewalk, Emagic, Mark of the Unicorn, Steinberg and others. One IMPORTANT point, the ShadowMix system has the audio in the fader, as well as the mute and solo functions. It requires one of the above DAW systems, and the DAW must be able to send audio out PRE FADER, as the ShadowMix system controls the audio \"just like the old days\". The fader tracks within .5dB from +12 on the fader to about -12, then starts to move away from the DAW screen, as it begins to double the resolution of the control data. This gives you more resolution below -12dB for mixing. From +12 to -12, it's great for tracks that have the audio mix in progress in that range, as they will translate pretty well. Of course, once it is in the analog domain, any mix that has been worked on only in the DAW will most likely require changes in the mix, so the importance of exact dB translation was traded for more resolution.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449356742759,"sku":"7657","price":4950.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_shadowmix_fader_automation.jpg?v=1787088688"},{"product_id":"tonelux-cr-detangler","title":"Tonelux CR Detangler","description":"This adapter goes on back of V rack for easier hookup of TL cabling. When using this card, you MUST place these modules on the left or right half of your Vrack in either order: FX2 (FX2+)x4, SM2, CR2 or CR2, SM2 and FX2 )FX2+)x4. \u003cbr\u003e\u003cbr\u003e You need to have a minimum of these above modules to make use of this card. As per Paul\/Tonelux, the use of this board saves approximately one day of labor, as opposed to hand wiring a system without the use of the board. 4x dsub to dsub ribbon jumpers are required connect this card to the V rack. A maximum of 3 feet in length is recommended. The card can be mounted to the NEW STYLE V racks that are now being shipped tie bars, or the card can be mounted remotely. The card has optional surface mounted XLR outputs that can be added.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449357004903,"sku":"13014","price":499.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_cr_detangler.jpg?v=1787088689"},{"product_id":"tonelux-8-channel-v8-roadster-unloaded-demo-deal","title":"Tonelux 8 Channel V8 Roadster - Unloaded (Demo Deal)","description":"The \u003cspan style=\"font-weight: bold;\"\u003eTonelux V8 Roadster\u003c\/span\u003e can be custom-loaded with any one of 20 different Tonelux Custom Console Modules to create any portable rig you can envision. D-sub and XLR ins \u0026amp; outs make this a snap to quickly connect\/disconnect in the studio. Expand later with a V-Rack and\/or a Tonelux full blown frame console!\u003cbr\u003e\u003cbr\u003eThe\u003cspan style=\"font-weight: bold;\"\u003e \u003c\/span\u003eV8\u003cb\u003e \u003c\/b\u003eincludes many features not found on any other rack system available today. \u003cbr\u003e\u003cbr\u003e The rack can house up to 8x Mic Pres, Eqs and Compressors, in any combination. \u003cbr\u003e\u003cbr\u003e The rack can also house any of the MIXING modules, including the MX2, FX2, MX5.1, SM2, TR8, and the CR2 for monitoring. \u003cbr\u003e\u003cbr\u003e The system pictured above is an 8) channel mixer with 2) MP1A Mic Pres and 2) EQ4P Equalizers. \u003cbr\u003e\u003cbr\u003e Having a Vrack back at the studio filled with MX2s and a CR2 module can link to the portable rack which allow both racks become one large system! \u003cbr\u003e\u003cbr\u003e \u003cb\u003eThese features include:\u003c\/b\u003e\u003cul\u003e \u003cli\u003e8x Module Slots \u003c\/li\u003e\n\u003cli\u003eXLR inputs and outputs for the Input, Insert Return\/Side Chain, and Output \u003c\/li\u003e\n\u003cli\u003eD-SUB inputs and outputs for the Input, Insert Return\/Side Chain, and Output \u003c\/li\u003e\n\u003cli\u003eD-Sub BUS linking to the VRack System to expand bussing, etc. \u003c\/li\u003e\n\u003cli\u003eLarge Power Supply, can power an additional VRack Aux power connector on rear. \u003c\/li\u003e\n\u003cli\u003eFolding Handle \u003c\/li\u003e\n\u003cli\u003eRubber feet on side and bottom \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449367949415,"sku":"15048","price":635.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_8_channel_v8_roadster_unloaded_1.jpg?v=1787088735"},{"product_id":"tonelux-aux1-buss-access-module-demo-deal","title":"Tonelux AUX1 Buss Access Module (Demo Deal)","description":"The \u003cb\u003eTonelux AUX1 \u003c\/b\u003eis a simple BUS access module that allows the user to insert an additional mixer, mic pre, etc. into the Tonelux MIX BUS. Each input is BALANCED and is calibrated for a level of +4 dBu \u003cp\u003e The LED at the bottom of the module indicates the mode that the AUX1 is in. Internally, there are headers that allow you to switch the jacks from the MX2 Stereo Mixer's busses to the MX5.1 Surround Mixer's busses, since any combination of modules can be used at the same time in the rack.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449367982183,"sku":"16321","price":299.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_aux1_buss_access_module_1.jpg?v=1787088735"},{"product_id":"tonelux-eq4p-module-demo-deal","title":"Tonelux EQ4P Module (Demo Deal)","description":"The \u003cb\u003eTonelux EQ4P\u003c\/b\u003e is a DISCRETE Parametric Equalizer with some very unique features. Notice that the panel has no Q control. The filter Q control is in relation to the Boost and Cut control, and uses a \"Constant Energy Curve\" that keeps the bandwidth wider at lower boost or cut levels and becomes narrow at higher boost or cut levels. This is musically pleasing. The curve is identical to many classic equalizers and is one of the reasons they are preferred over newer designs. When the PEAK button pressed, the 3 yellow \"peak\" buttons keep the width at a constant 1\/3 octave for more precision control. \u003cp\u003eThe High Frequency has a Shelving button instead of a Peak button. Since the Constant Energy Curve is so broad in the lower frequencies, there is no need for a low frequency shelf button. \u003c\/p\u003e\u003cp\u003eWith 4 bands of controls, each of the lower 2 have slightly different frequencies, allowing the lower band to go to 16 Hz, and the upper 2 bands are identical. The IN button is a silent IN\/OUT button that does not bypass the unit, but it bypasses the filters.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368047719,"sku":"13960","price":495.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_eq4p_module_1.jpg?v=1787088735"},{"product_id":"tonelux-mp1a-module-demo-deal","title":"Tonelux MP1A Module (Demo Deal)","description":"The \u003cb\u003eTonelux MP1a\u003c\/b\u003e is a DISCRETE mic preamp with a DIRECT INPUT on the front panel. The MIC IN is transformer coupled in and out, and has a 20 dB PAD switch (effects both MIC and DIR), a 48V Phantom switch and a Phase or POLARITY switch. The PAD and POLARITY switches effect both inputs. Identical to the MP1, but with the addition of an OUTPUT FADER to control the record level of the Mic Pre Output. The inner, or larger (silver) knob sets the mic pre gain and the outer smaller (black) knob controls the output level. We chose the fader control for the outer knob so the gain knob, once set, won't be bumped when adjusting the output level. \u003cbr\u003e\u003cbr\u003e The 8 seg LED VU meter follows the balanced output of the preamp. The level of the VU meter is adjustable over the entire range from off to +28. The PEAK led is set at +14VU or +18 dBu and can grab a fast peak and display it. With the \"a\" version, an internal jumper selects the MIC PRE MAIN OUTPUT or the MIC PRE GAIN STAGE signal to feed the VU Meter. This allows the engineer to monitor the real mic pre gain or the output level of the MP1a. When monitoring the Mic Pre Gain, the meter shows the actual gain stage level, and is not effected by the output fader. \u003cbr\u003e\u003cbr\u003e The Combo XLR\/Direct input is for use with a hi-z instrument, etc. The TILT tone control works with both the MIC in and DIR in and has it's own TILT EQ IN switch, which is a hard wire bypass switch when out. When turned up, the tilt control has a 0 to 6 dB boost on the high end while cutting the low end the same. If it is turned down, tilt will boost the low end up to 6 dB and cut the high end up to 6 dB. \u003cbr\u003e\u003cbr\u003e The Front panel XLR is multed to the rear panel XLR and that is also multed to the D-Sub \"INPUT\" on the rear of the V-Rack. The \"INSERT RETURN\" input of the V-Rack is a resistor isolated mic level input, that can be used when the MP1 is in a live recording situation and there is no splitter. It will bridge the mic line with 10X the impedance to minimize loading of the microphone. \u003cbr\u003e\u003cbr\u003e Included with the MP1a Mic Pre is the ability to PFL the output to an external amplifier or to the mixer\/master section for previewing the signal directly off the mic pre output.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368080487,"sku":"15228","price":545.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mp1a_module_1.jpg?v=1787088736"},{"product_id":"tonelux-lfe-module-demo-deal","title":"Tonelux LFE Module (Demo Deal)","description":"Tonelux TX-LFE 80\/120 Hz Sub Woofer Filter","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368113255,"sku":"13961","price":395.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_lfe_module_1.jpg?v=1787088735"},{"product_id":"tonelux-mx2d-module-demo-deal","title":"Tonelux MX2D Module (Demo Deal)","description":"The \u003cb\u003eTonelux MX2D Mixer\u003c\/b\u003e is a stereo line mixer with many features of a large frame console. The MX2 has a unique MUTE circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare. The SOLO button is both a AFL or PFL, allowing both functions to be selected globally in the Control Room Section. \u003cp\u003eThe FADER knob is the channel fader, with the ability to insert an external fader from the rear panel. \u003c\/p\u003e\u003cp\u003eThe PAN control is a standard stereo pan circuit with a center detent. \u003c\/p\u003e\u003cp\u003eThe INSERT button can act as a balanced insert for outboard equipment, or it can be used as a MIC PRE\/TAPE PLAY switch for live recording to check the mic pre output and then the output of the machine for confidence checks or post recording playback without repatching anything. \u003c\/p\u003e\u003cp\u003eThe ST button turns on the stereo bus, which allows the module to send to the aux sends without going to the stereo bus. \u003c\/p\u003e\u003cp\u003eThe Polarity switch is a standard phase inverter for the main signal path. \u003c\/p\u003e\u003cp\u003eThe 4 sends are internally configurable for PRE or POST fader signal. The MX2 has an optional DIRECT transformer output.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368146023,"sku":"13962","price":475.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mx2d_module_1.jpg?v=1787088736"},{"product_id":"tonelux-v-rack-demo-deal","title":"Tonelux V-Rack (Demo Deal)","description":"The \u003cb\u003eTonelux V-RACK\u003c\/b\u003e accommodates 16 Tonelux Modules in any combination.\u003cbr\u003e\u003cbr\u003e\u003cul\u003e\n\u003cli\u003e16 spaces (D-Sub in\/out)\u003c\/li\u003e\n\u003cli\u003e3U high\u003c\/li\u003e\n\u003cli\u003e2 V Racks per PSU\u003c\/li\u003e\n\u003cli\u003eV Rack is the core building block of Tonelux consoles.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368178791,"sku":"15230","price":399.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_v-rack_1.jpg?v=1787088736"},{"product_id":"tonelux-vu4-vu-meter-demo-deal","title":"Tonelux VU4 VU Meter (Demo Deal)","description":"The \u003cb\u003eTonelux model VU4\u003c\/b\u003e metering module allows inserting a metering system between any signal in the Tonelux modular setup. The VU4 will not load the signal significantly, as it has an input impedance of over 100K. With the ability to accept two separate signals from two sources, the VU4 can be used as a “Source\/Tape” metering system with external control over the switching of all meters.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368211559,"sku":"15231","price":455.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_vu4_vu_meter_1.jpg?v=1787088736"},{"product_id":"tonelux-tilt-demo-deal","title":"Tonelux Tilt (Demo Deal)","description":"The famous Tonelux MP1A TILT EQ control in a 19” rack mount unit. The \u003cspan style=\"font-weight: bold;\"\u003eTonelux TILT\u003c\/span\u003e includes 8) TILT EQ controls with an IN\/OUT switch, and a POLARITY switch on each channel. Channels 1 and 2 have XLR inputs and outputs, and channels 1-8 also come out on D-SUBS. The input and outputs are fully balanced. \u003cbr\u003e \u003cbr\u003eA very inexpensive way to equalize 8 channels with a unique single knob control.The famous Tonelux MP1A TILT EQ control in a 19” rack mount unit. The TILT includes 8) TILT EQ controls with an IN\/OUT switch, and a POLARITY switch on each channel. Channels 1 and 2 have XLR inputs and outputs, and channels 1-8 also come out on D-SUBS. The input and outputs are fully balanced. A very inexpensive way to equalize 8 channels with a unique single knob control.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449368244327,"sku":"16807","price":2050.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tilt_1.jpg?v=1787088736"},{"product_id":"tonelux-mp5a-module","title":"Tonelux MP5A 500 Series Microphone Preamp\/DI","description":"\u003cp\u003eSporting a smart design and offering versatile tone, the \u003cstrong\u003eTonelux MP5A\u003c\/strong\u003e mic preamp is a worthy addition to any 500 Series rack. One of the most popular features onboard the discrete MP5A is its now-famous \"Tilt\" circuit, effectively a Baxandall boost\/cut filter. Turn it one way to boost the highs and cut the lows, turn it the other way to boost the lows and cut the highs. However you use it, the \"Tilt\" circuit offers a uniquely useful shaping solution on the way in and may be all the EQ you need. Helpful metering and a smart gain system round out the Tonelux MP5A.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAdjust gain while keeping the tone you've dialed in\u003c\/li\u003e\n\u003cli\u003ePopular \"Tilt\" circuit offers sweetening\u003c\/li\u003e\n\u003cli\u003eSmart LED VU metering system keeps you informed\u003c\/li\u003e\n\u003cli\u003e48V phantom power and switchable front-panel DI\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003cstrong\u003eAdjust gain while keeping the tone you've dialed in\u003c\/strong\u003e\u003cbr\u003eThe Tonelux MP5A offers two knobs for gain adjustment, mic preamp gain and output gain that Tonelux dubs the \"fader.\" That way, you can set the tone you like with the preamp gain, then keep the tone but scale it back when you go into your converters. Another helpful feature onboard the MP5A is that the gain control goes all the way down to zero, whereas most pres stop at 6dB. The extra 6dB of loss can be really useful when you're miking a snare and you're right at the edge of peaking, letting you dial it back rather than engage the pad which would change the tone you already dialed in.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePopular \"Tilt\" circuit offers sweetening\u003c\/strong\u003e\u003cbr\u003eA special feature onboartd the MP5A is its \"Tilt\" circuit, an integrated Baxendall boost\/cut filter. When you turn it to the right, you boost the highs and cut the lows, with the opposite effect when you turn it to the left. Most often studios set it right around 1:00, which would provide just enough to make the high end clearer while pulling out mud from the lows. While the \"Tilt\" circuit is fully bypassable, it's a very useful little knob you'll come to love.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSmart LED VU metering system keeps you informed\u003c\/strong\u003e\u003cbr\u003eWhere many 500 Series modules skimp on the metering front, the MP5A makes sure you stay in the know. The green\/yellow section can display either the mic preamp gain or the output of the entire amplifier doing the gain. The peak LED, however, follows the mic preamplifier so you know what to dial back.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003e48V phantom power and switchable front-panel DI\u003c\/strong\u003e\u003cbr\u003eIn addition to rear-panel connectivity, the MP5A offers a combination XLR and 1\/4\" input on the front, with a hi-Z switch for use as a convenient DI. The 48V LED meter lets you know when there's 48V detected, whether it's engaged on the MP5A or coming in from somewhere else, for example the front of house board, in which case you'd want to kick on the 48V switch to preserve the full voltage. The Tonelux MP5A also features a 180-degree phase flip switch that affects the 1\/4\" jack as well as the front and rear mic pre jacks.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449369096295,"sku":"16945","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_mp5a_4ae33bd8-3b70-47d7-97ee-fff71e97b185.jpg?v=1787088740"},{"product_id":"tonelux-eq5p-module","title":"Tonelux EQ5P 500 Series Parametric EQ","description":"\u003cp\u003eNot your everyday parametric EQ, The \u003cstrong\u003eTonelux EQ5P\u003c\/strong\u003e takes a nod in a historic direction with its \"Proportional Q\" approach, offering a pleasingly musical response with a curve identical to a number of classic EQs. When you need an EQ capable of surgery and one that's sweet but not overly so, the EQ5P does the trick, giving you four bands to pull out unwanted frequencies while retaining a natural, musical sound that's honest to the source. Arguably one of the most versatile 500 Series EQs available.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFlexible \"Proportional Q\" approach yields a classic sound\u003c\/li\u003e\n\u003cli\u003eOverlapping frequency bands give you broad control\u003c\/li\u003e\n\u003cli\u003eTop band offers shelving, bottom bands offer a fixed Q switch\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003cstrong\u003eFlexible \"Proportional Q\" approach yields a classic sound\u003c\/strong\u003e\u003cbr\u003eTonally, classic parametric EQs offered a bit more magic than most modern counterparts, thanks to their \"Proportional Q\" design. The Tonelux EQ5P draws on history, taking the same classic approach as its older brother the popular EQ4P. There are four parametric bands all with the \"Proportional Q\" effect available. Turn the boost all the way to one side and the Q becomes more narrow, just under an octave. If you turn it gradually from the center, you can go from a wide band of three octaves gradually down to that one octave. The broad-to-narrow nature keeps the EQ5P musical and also keeps you out of trouble by avoiding boosting too much in too narrow of a bandwidth.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eOverlapping frequency bands give you broad control\u003c\/strong\u003e\u003cbr\u003eThe Tonelux EQ5P offers overlapping frequency bands, each one continuously variable so you can dial in on exactly what you want to boost or cut. Then, you have a +\/-15dB boost or cut, with that \"Proportional Q\" effect. The top two bands are identical at 500Hz-21kHz. The EQ5P's third and fourth bands are nearly identical, with the bottom band going down a little lower at 50Hz-3kHz and 16Hz-1kHz respectively.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eTop band offers shelving, bottom bands offer a fixed Q switch\u003c\/strong\u003e\u003cbr\u003eOn the bottom three bands of the Tonelux EQ5P, you can switch to a fixed Q of a 1\/3 octave, letting you gradually notch something out if that's what you want. The top band offers a Shelving button that switches it into a shelving mode with a broad proportional Q effect. You can go from 500Hz on up to make things sound nice and bright. As the low frequency bands are broad, there's no need for a shelving switch there. Finally, the Tonelux EQ5P does offer an In\/Out switch that, by demand, switches out only the filters, so you're still getting the benefit of the circuit.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eTonelux EQ5P features:\u003c\/strong\u003e\u003cbr\u003e500 Series parametric EQ with 4 bands\u003cbr\u003eClassic \"Proportional Q\" effect from three octaves to one\u003cbr\u003eSwitchable Fixed Q on bands 2-4 for 1\/3 octave\u003cbr\u003eTop two bands are 500Hz-21kHz\u003cbr\u003eThird band is 50Hz-3kHz\u003cbr\u003eFourth band is 16Hz-1kHz\u003cbr\u003eIn\/Out switch bypasses filters but goes through the circuit\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449384071271,"sku":"16944","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_eq5p.jpg?v=1787088799"},{"product_id":"tonelux-tx5c-module","title":"Tonelux TX5C 500 Series Compressor","description":"\u003cp\u003eAcross the board, Tonelux manages to merge excellent sound with smart features you don't see on other units. The extraordinarily versatile, stereo-linkable \u003cstrong\u003eTX5C\u003c\/strong\u003e 500 Series compressor is the perfect example. In addition to offering both feed back and feed forward compression, the TX5C actually lets you blend the two, giving you the freedom of combining smoothness with aggression for the perfect hybrid. The Tonelux TX5C also uniquely offers in-module parallel compression with a wet\/dry mix knob. And to top it all off, Tonelux's \"Tilt\" circuit is onboard, giving you unique control over the sidechain to avoid pumping and get more of what you really want with the TX5C.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eBlendable feed back and feed forward compression add versatility\u003c\/li\u003e\r\n\u003cli\u003eWet\/dry mix knob for the perfect blend\u003c\/li\u003e\r\n\u003cli\u003eIntegrated \"Tilt\" circuit on the sidechain improves results\u003c\/li\u003e\r\n\u003cli\u003eFlexible ratio goes above and beyond the norm\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003cbr\u003e\u003cstrong\u003eBlendable feed back and feed forward compression add versatility\u003c\/strong\u003e\u003cbr\u003eWhen you want versatile compression, Tonelux added enough features into the TX5C to make it a no brainer for any 500 Series rack. For starters, it offers both feed back and feed forward compression, so you get the best of old-school smoothness and modern compression, making the TX5C effectively two compressors in one. Beyond that, however, the TX5C features a unique tone control, letting you fade between the two compression types and get the best attributes of each, giving you the most control over your sound.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eWet\/dry mix knob for the perfect blend\u003c\/strong\u003e\u003cbr\u003eThe TX5C lets you skip a step, foregoing in-the-box dry\/wet blending on two channels and letting you get just the right amount of each via in-module parallel mixing. However much you dial in, the TX5C gives you that extra something via its all discrete op-amp and all-discrete output stage with a TX-280 transformer.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eIntegrated \"Tilt\" circuit on the sidechain improves results\u003c\/strong\u003e\u003cbr\u003eIf you've ever used the Tonelux \"Tilt\" circuit on their other modules, you'll know this is a feature not to be ignored. Effectively a Baxendall boost\/cut filter, the \"Tilt\" circuit lets you filter the sidechain and control how the compressor reacts. Because you can increase the highs and decrease the lows simultaneously, you get a musical response that virtually eliminates pumping because the RMS detector gets more uniform energy distribution versus the bass-heavy signal most compressors see.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFlexible ratio goes above and beyond the norm\u003c\/strong\u003e\u003cbr\u003eControl your compression with the TX5C's ratio control, going from 1.5:1 to 20:1 and then even beyond via the \"Over\" feature. Using \"Over,\" you can cause the compressor to reduce at a higher ration than the gain is going into it. For example, the compressor can compress an increase in signal of 10dB with a gain reduction of up to -8dB, so if the signal goes up 10dB, the output will go down 8dB. It's a nice trick for taking an over-compressed source, say a snare. By adjusting the attack and using the Over feature, you can effectively recover the original impact peak of the snare. Then, with the wet\/dry mix control, you can blend back in the liveliness with the original \"flat\" snare to get a dynamic sound but with a controlled peak. Note also that the TX5C offers flexible attack and release settings, letting you switch from an extremely fast micro-second attack down to a smooth, slow, more leveling-like attack. Likewise, the release control can be adjusted from almost instant to three seconds. Auto makeup gain keeps the gain at unity, regardless of how much you're compressing.\u003cbr\u003e\u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449384136807,"sku":"16946","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_tx5c.jpg?v=1787088799"},{"product_id":"tonelux-fx2-module-used","title":"Tonelux FX2+ Module (used)","description":"\u003cp\u003eThe\u003cstrong\u003eTonelux FX2+ Mixer\u003c\/strong\u003eis a dual stereo line mixer with a simple pair of level controls and a pair of panners. \u003c\/p\u003e\r\n\u003cp\u003eThe Pan control is a standard stereo pan circuit with a center detent. The FX2 has a unique Mute circuit that when pressed, the LED turns RED, but when the module is ON, the LED serves as a level presence indicator, illuminating green to show signal presence. This is very useful in live recording when you need to know quickly if a channel has signal or which has the loudest signal on it. It is also perfect for identifying which channel has the Kick and which has the Snare.\u003c\/p\u003e\r\n\u003cp\u003eThe \u003cstrong\u003eFX2+ \"AUX MSTR\" \u003c\/strong\u003eis an Optional send master, which can be used in place of the SM1 or SM2 bus master when rack space is critical. It allows the rack to be filled with a full set of 16 modules, giving you 32 channels, including the masters, \u003cstrong\u003eall in one 3U rack\u003c\/strong\u003e.\u003c\/p\u003e\r\n\u003cp\u003eThe rear panel feature connector provides for an external fader for the send master option on the FX2+.\u003c\/p\u003e\r\n\u003cp\u003eThe FX2 can be used by it self as a inexpensive dual stereo mixer for DAW or LIVE use when a simple stereo bus is all that is required.\u003c\/p\u003e\r\n\u003cp\u003eWhen used with the MX2 series, the addition of 4 FX2 modules will give you 8 returns and the masters for the 4 sends on the MX2, saving you the space of having 4 SM1 master modules.\u003c\/p\u003e\r\n\u003cp\u003eThe FX2 can also be used as an additional set of sends, fed from the direct output of the MX2, as the outputs of each panner can be internally set to feed any of the 16 available busses in the VRACK, allowing up to 8 sends from each MX2, including the onboard set of 4 sends.\u003c\/p\u003e\r\n\u003cp\u003eThis module, when used as a simple external summing module, will bring down the cost of a DAW external mixing system considerably.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449404190823,"sku":"12890","price":337.5,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_fx2_used_pb_90a210a7-b7cd-4f40-bfbb-e4b556f3ed00.jpg?v=1787088871"},{"product_id":"tonelux-v-rack-16-input-channels","title":"Tonelux V-Rack 16 Input Channels","description":"Description coming soon.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449408417895,"sku":"18932","price":7559.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_v-rack_16_inputs_094d346b-9530-4b32-9649-35a3e1674284.jpg?v=1787088887"},{"product_id":"tonelux-otb-16","title":"Tonelux OTB-16","description":"\u003cp\u003e\u003cstrong\u003eNOTE: This item is currently back-ordered. Please call for estimated delivery times.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThe \u003cspan style=\"font-weight: bold;\"\u003eTonelux OTB16\u003c\/span\u003e is a 16 channel 1U mixer with 16 balanced inputs and a Tonelux discrete summing bus. Each channel has a level control and a panner. The access to the OTB16 is through 2 eight channel D-sub inputs at a level of +4dBu nominal.\u003cbr\u003e \u003cbr\u003e The summing of the 16 channels is through the famous Tonelux TX-240 and TX-260 discrete op-amps, and then through the main output transformer, which can be adjusted by the MASTER fader pot, which comes out of a pair of XLR connectors. Additionally there is a monitor output for monitoring or for expansion, which is balanced but transformer-less. Two additional balanced inputs to the MIX bus. The pre-fader monitor output can be plugged into the BUS input to extend the number of channels with a second or third OTB16. 120 or 230 volts AC powered 50\/60 Hz.\u003c\/p\u003e","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449408450663,"sku":"19104","price":1499.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_otb16_front_dad59656-c2a3-497c-b723-963502d0bcb4.jpg?v=1787088887"},{"product_id":"tonelux-v-rack-8x2-summing-rack","title":"Tonelux V-Rack 8x2 Summing Rack","description":"Description coming soon.","brand":"Tonelux","offers":[{"title":"Default Title","offer_id":44449408516199,"sku":"18651","price":8448.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/tonelux_8x2_2611e310-f6d3-48b5-b30d-9eb290a16ce8.jpg?v=1787088887"}],"url":"https:\/\/vintageking1.myshopify.com\/collections\/tonelux.oembed","provider":"VINTAGE KING AUDIO","version":"1.0","type":"link"}