{"title":"Power Sequencers \u0026 Relays","description":null,"products":[{"product_id":"furman-ps-8r-ii","title":"Furman PS-8R II","description":"\u003cp\u003eThe most widely recognized and trusted name in AC power conditioning is proud to introduce the PS-8R II power conditioner\/sequencer, featuring Furman’s revolutionary SMP+ technology.  Furman’s Series Multi-Stage Protection Plus (SMP+) circuit also features our exclusive Linear Filter Technology (LiFT) with Extreme Voltage Shutdown (EVS) and a high current TVZ-MOV.  Together, these technologies comprise what is, without question, the world’s most advanced and comprehensive transient voltage surge suppressor\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"bold_text\"\u003e\u003cstrong\u003eSMP+ (Series Multi-stage Protection Plus)\u003c\/strong\u003e\u003c\/span\u003e\u003cbr\u003eFurman’s SMP+ surge suppression virtually eliminates service calls.  Traditional surge suppression circuits are designed to just “sacrifice” themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor.  With Furman’s SMP+, however, damaging transient voltages are safely absorbed, clamped and dissipated.  No sacrificed parts, no service calls, no down time.\u003c\/p\u003e\n\u003cp\u003eUnique to Furman’s SMP+ is its unparalleled clamping voltage.  While other designs offer clamping voltages that are well above 300Vpk, Furman’s SMP+ clamps at 188Vpk, 133 VAC RMS even when tested with multiple 6000Vpk - 3000 amp surges!  This unprecedented level of protection is only available with Furman’s SMP+ technology.  Additionally, Furman’s trusted over-voltage circuitry protects against all too frequent accidental connections to 208 or 240VAC, by shutting off the incoming power until the over voltage condition is corrected.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan class=\"bold_text\"\u003eLiFT (Linear Filtering Technology)\u003c\/span\u003e\u003cbr\u003e\u003c\/strong\u003eUnfortunately, traditional AC fi lter - Conditioners have been designed for unrealistic laboratory conditions.  Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs.  Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line!  Worse still, lost digital data, the need to re-boot digital pre-sets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground.  Furman’s SMP+ with LiFT takes another approach, ensuring optimal performance through linear fi ltering and no leakage to ground.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"bold_text\"\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan class=\"bold_text\"\u003eOptional Accessories\u003c\/span\u003e\u003cbr\u003eGN-I or GN-LED:\u003c\/strong\u003e These gooseneck lights (either incandescent or LED) are the perfect accessory to any Series II unit.  They plug into the BNC jack on the rear panel to conveniently illuminate the rear of your rack.  These versatile lights can also be used with a variety of other products in other applications.\u003c\/p\u003e\n\u003cp\u003ePS-REL Relay:  Allows a PS-8R II to be turned on by sensing AC at a preamp’s switched outlet; also allows daisy-chaining for 6 or more delayed outlet groups.\u003c\/p\u003e\u003c\/span\u003e\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272660071,"sku":"5733","price":299.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_ps8r2_1_39591208-45d1-4500-af8f-838955e48d24.jpg?v=1787088390"},{"product_id":"furman-ps-pro-ii","title":"Furman PS-PRO II","description":"\u003cp\u003eThe most widely recognized and trusted name in AC power conditioning is proud to introduce the \u003cstrong\u003ePS-PRO II \u003c\/strong\u003epower conditioner \/ sequencer, featuring Furman’s revolutionary SMP+ technology.  Furman’s Series Multi-Stage Protection Plus (SMP+) circuit also features our exclusive Linear Filter Technology (LiFT) coupled with Extreme Voltage Shutdown (EVS) and a high current TVZ-MOVs.  Together, these technologies comprise what is, without question, the world’s most advanced and comprehensive transient voltage surge suppressor. \u003cbr\u003e\u003cbr\u003eSMP+ (Series Multi-stage Protection Plus) Furman’s virtually maintenance-free SMP+ surge suppression virtually eliminates service calls.  Traditional surge suppression circuits “sacrifi ce” themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. With Furman’s SMP+, however, damaging transient voltages are safely absorbed, clamped and dissipated. No sacrificed parts, no service calls, no down time. Unique to Furman’s SMP+ is its unparalleled clamping voltage. \u003cbr\u003e\u003cbr\u003eWhile other designs offer clamping voltages that are well above 300Vpk, Furman’s SMP+ clamps at 188Vpk, 133 VAC RMS even when tested with multiple 6000Vpk - 3000 amp surges! This unprecedented level of protection is only available with Furman’s SMP+ technology.  Additionally,Furman’s trusted over-voltage circuitry protects against all too frequent accidental connections to 208 or 240VAC, by shutting off the incoming power until the over voltage condition is corrected. \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eLiFT (Linear Filtering Technology)\u003c\/strong\u003e\u003cbr\u003eUnfortunately, traditional AC filter - Conditioners have been designed for unrealistic laboratory conditions.  Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs.  Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line!  Worse still, lost digital data, the need to re-boot digital pre-sets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground.  Furman’s SMP+ with LiFT takes another approach, ensuring optimal performance through linear fi ltering and no leakage to ground. \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFeatures\u003c\/strong\u003e\u003cbr\u003eThe PS-PRO II Power Conditioner\/Sequencers is capable of powering up a rack full of equipment in a three-step delayed sequence.  The sequence is reversed for power-down.  The sequence can be initiated with either momentary or maintained switches, locally or remotely.  A duplex outlet is provided for each delay step. A front panel screwdriver adjustment sets the delay time for the PS-PRO II.  The PS-PRO II also features a locking switch with a removable key for maximum security. One or more Furman PS-PRO II’s may be installed in remote locations and operated via low-voltage wiring.  The PS-PRO II includes a rear mounted BNC jack which accepts any standard (12VAC, 0.5A) gooseneck lamp for rear rack illumination, as well as a front panel switch which controls the gooseneck’s operation.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePS-REL Relay Accessory: \u003cbr\u003e\u003c\/strong\u003eAllows a PS-PRO II to be turned on by sensing AC at a preamp’s switched outlet; also allows daisy-chaining for 6 or more delayed outlet groups. \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eOptions \u003c\/strong\u003e\u003cbr\u003eModels PS-PRO E II: “E” suffix versions are for use in countries with 220\/240 volt AC lines.  Furman Power Conditioner \/ Sequencers use internationally- accepted IEC-320 connectors.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272823911,"sku":"5744","price":439.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_ps_pro2_1.jpg?v=1787088390"},{"product_id":"furman-acd-100","title":"Furman ACD-100","description":"\u003cp\u003eThe \u003cstrong\u003eACD-100 AC Power Distro\u003c\/strong\u003e is an extremely compact, low cost rack-mount power distribution system that is ideal for touring PA systems, touring musical and theatrical acts, mobile recording facilities, on-location film and video shoots, etc.-any situation where AC power must be distributed to multiple circuits and a hard-wired, built-in system is missing, inadequate, or impractical.  Use of a Power Distro is cost-effective, both in terms of the convenience it offers and the elimination of bulky and expensive parallel feeds and related connectors.\u003c\/p\u003e\n\u003cp\u003eThe ACD-100 can handle up to 100 amps of incoming power, distributing it to five 20 amp, 120V circuits.  Each circuit has a neon status indicator that lights up when its breaker is turned on, and a 20 amp duplex outlet on the rear panel.\u003c\/p\u003e\n\u003cp\u003eThe circuit breakers used in the ACD-100 are high-inrush magnetic types designed specifically for critical data processing and broadcast applications where nuisance tripping cannot be allowed.  They have a pulse tolerance of 10 times the rated current, or 200 amperes.  This makes them particularly suited for use with power amps and other devices with high-reactance loads, since the high pulse tolerance will keep them from tripping falsely at the instant power is applied or on musical peaks.  If a breaker should trip, it can be reset as soon as the overload is corrected-there is no cool-down delay time required.  Temperature compensations which affect fuses and inexpensive thermal breakers are not a concern.  The breakers are of the highest industrial grade, UL\/CSA listed, precise in operation and rugged in construction.  They may be used as on-off switches for the five circuits.\u003c\/p\u003e\n\u003cp\u003eThe ACD-100's design incorporates four oversized busses, allowing wiring for 120V or 240V single phase, or 208V three phase power.  A strain relief clamp is provided that can accommodate a cable or wire bundle up to 1.5 inches in diameter.  Cable termination is a simple process of breaking out and stripping the individual conductors and connecting them with set screws, and then tightening the strain relief clamp.  Complete instructions accompanying the unit guide the user through the process of selecting and terminating the supply cable.\u003c\/p\u003e\n\u003cp\u003eThe ACD-100 provides basic spike and surge suppression, with metal oxide varistors (MOV's) connected between the hot and neutral conductors of each circuit.  The MOV's respond to line-derived spikes in nanoseconds, clamping transient voltages to safe levels of 200V peak or less.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272889447,"sku":"5745","price":564.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_acd100_1.jpg?v=1787088391"},{"product_id":"furman-asd-120","title":"Furman ASD-120","description":"\u003cp\u003eThe \u003cstrong\u003eASD-120 AC Sequenced Power Distro\u003c\/strong\u003e is an extremely compact, low cost rackmount power distribution system that is ideal for touring PA systems, touring musical and theatrical acts, mobile recording facilities, on-location film and video shoots, etc. - any situation where AC power must be distributed to multiple circuits and a hard-wired, built-in system is missing, inadequate, or impractical.  Use of a Power Distro is cost-effective, both in terms of the convenience it offers and the elimination of bulky and expensive parallel feeds and related connectors.  The ASD-120 offers many more features as well.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThe ASD-120 allows you to power up and its six circuits in a sequenced fashion.  The sequence is reversed for power down.  The delay interval is user-adjustable via an internal trimpot.\u003c\/p\u003e\n\u003cp\u003ePower sequencing is needed whenever various kinds of equipment must be powered up or down in groups, rather than all simultaneously.  In audio systems, sequenced powering is often necessary to allow turn-on transients from low level amplifiers and processors to settle down before any power amps are turned on, because simultaneous powering would result in a loud, annoying, and potentially destructive \"pop\" reaching the speakers.  And in any large system whose components present an inductive load to the AC line (including electric motors, power supplies, and power amplifiers of all kinds), sequenced powering can avoid excessive inrush currents that cause circuit breakers to trip even though the steady-state currents are not excessive.\u003c\/p\u003e\n\u003cp\u003eThe ASD-120's front panel provides a three-position switch for each circuit that allows each circuit to be part of the power up\/down sequence, or to remain on or off apart from the sequence.  An LED that indicates when either the power-up or power-down sequence is in progress.  The sequence can be initiated with either momentary or maintained switches, locally or remotely.  A duplex outlet is provided for each delay step.  A locking switch with a removable key is provided for maximum security.\u003c\/p\u003e\n\u003cp\u003eSince the sequence control signals are also available on the rear panel, one or more ASD-120's may be installed in remote locations and operated via low-voltage control wiring.  The sequence control signals can also drive PowerPorts, MiniPorts, PS-PRO and PS-8-R Power Sequencers, or any other circuits that need to know when their particular time delay has elapsed.  Using one or more ASD-120's can provide the capability of controlling power and power sequencing for an entire system.\u003c\/p\u003e\n\u003cp\u003eThe ASD-120 can handle up to 120 amps of incoming power, distributing it to six 20 amp, 120V circuits.  Each circuit has a front panel status indicator that lights up when it is turned on, and a 20 amp duplex outlet on the rear panel.\u003c\/p\u003e\n\u003cp\u003eThe ASD-120's design incorporates four oversized busses, allowing wiring for 120V or 240V single phase, or 208V three phase power.  A strain relief clamp is provided that can accommodate a cable or wire bundle up to 1.5 inches in diameter.  Cable termination is a simple process of breaking out and stripping the individual conductors and connecting them with set screws, and then tightening the strain relief clamp.  Complete instructions accompanying the unit guide the user through the process of selecting and terminating the supply cable.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272922215,"sku":"5746","price":699.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_asd120_1.jpg?v=1787088391"},{"product_id":"furman-powerlink","title":"Furman Powerlink","description":"\u003cp\u003eThe new \u003cstrong\u003ePowerLink \u003c\/strong\u003eis a compact, low-cost rackmount Remote Sequencer that provides timing and switching for up to six power control devices, turning them on and off in a preset sequence.  The power-down sequence is opposite to the power-up sequence - the last device to be turned on will be the first turned off, etc.  The delay interval between the turn-on or turn-off of each device and the next device in sequence is user-adjustable from 0.2 to 10 seconds, via an internal trimpot.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eA PowerLink is intended to work with a group of relay-controlled power outlets such as Furman MiniPorts, to create a very flexible power control system that can expand to handle as many circuits carrying as much current as needed.\u003c\/p\u003e\n\u003cp\u003eAn on or off sequence can be initiated from the PowerLink itself, using the built-in locking key switch, or, if the key switch is set to enable Remote operation, by one or more momentary or maintained-action switches in distant locations.\u003c\/p\u003e\n\u003cp\u003eThe outputs of the PowerLink are low power relay contacts, accessible via rear-panel screw terminal strips.  Outputs may be configured to be normally-closed or normally-open by positioning internal \"suitcase\" jumpers.  All input and output commons are electrically isolated to avoid the creation of ground loops.\u003c\/p\u003e\n\u003cp\u003ePower sequencing is needed whenever various kinds of equipment must be powered up or down in groups, rather than all simultaneously. In audio systems, sequenced powering is often necessary to allow turn-on transients from low level preamplifiers and processors to settle down before any power amps are turned on. This is because simultaneous powering can result in a loud, annoying, and potentially destructive \"pop\" reaching the speakers.  Also, In any large system whose components present an inductive load to the AC line (including electric motors, power supplies, and power amplifiers of all kinds), sequenced powering can avoid excessive in rush currents that can cause circuit breakers to trip even though the steady-state currents are not excessive.\u003c\/p\u003e\n\u003cp\u003eThe user has complete control of each of the PowerLink's outputs.  A three-position front panel switch for each control output allows that output to be included in the sequence, or permits overriding the sequence to switch that output on or off independently of the sequence timing.  Indicator LED's light up to show when each output is in the \"on\" state.\u003c\/p\u003e\n\u003cp\u003eWhile the PowerLink is ideal for controlling MiniPorts, it can also control Furman PowerPorts, PS-PRO or PS-8R Power Sequencers, ASD-120 Sequenced Power Distros, or any other devices that need to be switched when a particular time delay has elapsed.  A PowerLink can even control one or more other remotely-located PowerLinks, providing complete power sequencing control for even the very largest systems.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272954983,"sku":"5747","price":399.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_powerlink_1.jpg?v=1787088391"},{"product_id":"furman-powerport","title":"Furman PowerPort","description":"\u003cp\u003e\u003cstrong\u003ePowerPorts\u003c\/strong\u003e comprise the building blocks of Furman's versatile new high performance power conditioning and distribution system, intended for medium size to the largest audio, video, and multimedia installations.  Such a system can grow to any size, yet be conveniently controlled from any location.  An individual PowerPort provides control, timing, monitoring, and power conditioning capability for a single equipment site. All critical circuit functions are governed by an internal microprocessor.\u003c\/p\u003e\n\u003cp\u003ePowerPorts offer the same renowned RFI\/EMI and spike\/surge protection as Furman's top-of-the-line PRO Series rackmount power conditioners.  A PowerPort can safely absorb up to a whopping 11,000 amperes of spike\/surge current in any mode (hot-neutral, neutral-ground, or hot-ground), using a unique array of protection devices including MOV's, gas discharge tubes, high voltage inductors and capacitors, and fast-blow fuses.  It also provides over 60 dB of common-mode attenuation in the 1-200 MHz RF band.\u003c\/p\u003e\n\u003cp\u003eAn additional feature, Extreme Voltage Shutdown, fights a hazard particularly common in the entertainment industry: wiring faults -- for example, accidental connection to 220V.  It senses voltages that are so high or low that operation would be impossible (under 80V or over 140V) and shuts the power down before damage can occur. An \"Extreme Voltage\" LED blinks a red alert when an abnormal voltage causes shutdown.  Other status indicators (\"Protection OK\" and \"Ground OK\") monitor the integrity of the protection devices and grounding, and report if the protection is compromised.  A \"Mains OK\" LED glows steady for normal input voltage and blinks a warning for marginal but not extreme voltages (80-90V or 130-140V).\u003c\/p\u003e\n\u003cp\u003eAs a power sequencer, PowerPort has independent turn-on and turn-off delays, with simple daisy chaining for remote switching of single or an unlimited number of multiple units.  Control wiring can be up to five miles in length without performance degradation, based on using 24 AWG.  The PowerPort has two modes of operation: maintained and momentary.  These terms refer to the type of switch that is attached to the remote terminals, and determine the functionality of the unit.  The mode may be easily changed by moving a suitcase jumper on the circuit board.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449272987751,"sku":"5748","price":359.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_powerport_1.jpg?v=1787088391"},{"product_id":"furman-mp-15","title":"Furman MP-15","description":"\u003cp\u003eThe \u003cstrong\u003eFurman MINIPORT-20 Power Relay\u003c\/strong\u003e is a UL\/CUL listed, 20 amp, relay switched 120 VAC outlet, with a terminal strip that allows remote control via safe, inexpensive, low voltage Class 2 wiring.  Also available is the MINIPORT-15, which is functionally identical except for its 15 amp rating.  Both models include an internal 12 VDC supply, and can be controlled from a remote location with maintained or momentary contact switches.\u003c\/p\u003e\n\u003cp\u003eMultiple MINIPORTs may be connected together so that all are controlled by a single switch closure, and may be linked so that all turn on simultaneously or one by one, in a delayed sequence.  If delayed, the delay interval between the turn-on of one MINIPORT and the next is approximately three seconds.  (Delayed turn-on is useful in avoiding large inrush currents that can trip house circuit breakers, that would otherwise occur if all amps were turned on simultaneously.)  Turn-off always occurs simultaneously, however.\u003c\/p\u003e\n\u003cp\u003eA Furman PowerLink can also be used to control MINIPORT(s).  In this use, the MINIPORT(s) areconnected to terminals on the PowerLink, which provide the necessary control functions. MINIPORTs are similarly compatible with the Furman PowerPort and ASD-120 Sequenced Power Distro.  With the addition of a PS-REL AC Relay to provide control, a MINIPORT can be used to extend the capacity of any other Furman power product — or, for that matter, any product with a switched outlet, such as a receiver\/ amp controlled with a wireless remote.  When used in this manner, the MINIPORT is switched on or off when the outlet that the PS-REL is plugged into goes on or off.\u003c\/p\u003e\n\u003cp\u003eBoth the MINIPORT-15 and the MINIPORT-20 come equipped with two knockout holes for permanent installation with 1\/2\" conduit — one on the top surface, the other on the bottom.  Use of the bottom knockout hole requires removing the AC cord.  According to the National Electrical Code, 1\/2\" conduit can accommodate up to five 20 amp circuits using ten THWN 12 gauge stranded wires; however, local codes should be checked for exact requirements.\u003c\/p\u003e\n\u003cp\u003eMINIPORTs are housed in rugged steel enclosures and come equipped with a heavy duty, 10 foot AC cord.  The MINIPORT-15 is fused; the MINIPORT-20 is equipped with a precision magnetic circuit breaker. The MINIPORT-20 and MINIPORT-15 are UL and CUL (Canadian) listed.  Note: because of its UL listed 20 amp rating, the MINIPORT-20 uses a 20 amp AC plug with perpendicular (not parallel) blades.  If in doubt regarding your installation, please consult an electrician or call the factory. The MINIPORT-20 is an upgrade of an earlier Furman MINIPORT.  The primary differences are the ability to use momentary switches, the delayed turn-on option, and the additional knockout holes.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"bold_text\"\u003eDimensions:\u003c\/span\u003e 5.5\" (H) x 3.75\" (W) x 2\" (D). With mounting bracket, width is 5.25\".\u003c\/p\u003e\n\u003cp\u003eThe MINIPORT-15Q (15amp) and the MINIPORT-20Q (20amp) provide a pair of remotely activated, relay-controlled outlets which are both set up for mounting in any standard electrical Quad Box, either directly or with a \"mud ring\" attached.\u003c\/p\u003e\n\u003cp\u003eDue to the space limitations of a Quad Box, the \"Q\" MINIPORT models have a smaller feature set than the MINIPORT-15 and MINIPORT-20.  The MP-15Q and MP-20Q have no internal power supply; a maintained 10-30VDC supply capable of supplying 10 mA is required to turn on the outlets.  This can be supplied by a Furman PowerLink, ASD-120 or PS-8R (with a simple internal modification to the PS-8R). UL, C-UL pending.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449273118823,"sku":"5749","price":119.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_mp15.jpg?v=1787088391"},{"product_id":"furman-mp-20","title":"Furman MP-20","description":"\u003cp\u003eThe \u003cstrong\u003eFurman MINIPORT-20 Power Relay \u003c\/strong\u003eis a UL\/CUL listed, 20 amp, relay switched 120 VAC outlet, with a terminal strip that allows remote control via safe, inexpensive, low voltage Class 2 wiring. Also available is the MINIPORT-15, which is functionally identical except for its 15 amp rating.  Both models include an internal 12 VDC supply, and can be controlled from a remote location with maintained or momentary contact switches.\u003c\/p\u003e\n\u003cp\u003eMultiple MINIPORTs may be connected together so that all are controlled by a single switch closure, and may be linked so that all turn on simultaneously or one by one, in a delayed sequence. If delayed, the delay interval between the turn-on of one MINIPORT and the next is approximately three seconds.  (Delayed turn-on is useful in avoiding large inrush currents that can trip house circuit breakers, that would otherwise occur if all amps were turned on simultaneously.)  Turn-off always occurs simultaneously, however.\u003c\/p\u003e\n\u003cp\u003eA Furman PowerLink can also be used to control MINIPORT(s).  In this use, the MINIPORT(s) areconnected to terminals on the PowerLink, which provide the necessary control functions. MINIPORTs are similarly compatible with the Furman PowerPort and ASD-120 Sequenced Power Distro.  With the addition of a PS-REL AC Relay to provide control, a MINIPORT can be used to extend the capacity of any other Furman power product — or, for that matter, any product with a switched outlet, such as a receiver\/ amp controlled with a wireless remote.  When used in this manner, the MINIPORT is switched on or off when the outlet that the PS-REL is plugged into goes on or off.\u003c\/p\u003e\n\u003cp\u003eBoth the MINIPORT-15 and the MINIPORT-20 come equipped with two knockout holes for permanent installation with 1\/2\" conduit — one on the top surface, the other on the bottom.  Use of the bottom knockout hole requires removing the AC cord.  According to the National Electrical Code, 1\/2\" conduit can accommodate up to five 20 amp circuits using ten THWN 12 gauge stranded wires; however, local codes should be checked for exact requirements.\u003c\/p\u003e\n\u003cp\u003eMINIPORTs are housed in rugged steel enclosures and come equipped with a heavy duty, 10 foot AC cord.  The MINIPORT-15 is fused; the MINIPORT-20 is equipped with a precision magnetic circuit breaker.  The MINIPORT-20 and MINIPORT-15 are UL and CUL (Canadian) listed.  Note: because of its UL listed 20 amp rating, the MINIPORT-20 uses a 20 amp AC plug with perpendicular (not parallel) blades.  If in doubt regarding your installation, please consult an electrician or call the factory. The MINIPORT-20 is an upgrade of an earlier Furman MINIPORT.  The primary differences are the ability to use momentary switches, the delayed turn-on option, and the additional knockout holes.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"bold_text\"\u003eDimensions:\u003c\/span\u003e 5.5\" (H) x 3.75\" (W) x 2\" (D). With mounting bracket, width is 5.25\".\u003c\/p\u003e\n\u003cp\u003eThe MINIPORT-15Q (15amp) and the MINIPORT-20Q (20amp) provide a pair of remotely activated, relay-controlled outlets which are both set up for mounting in any standard electrical Quad Box, either directly or with a \"mud ring\" attached.\u003c\/p\u003e\n\u003cp\u003eDue to the space limitations of a Quad Box, the \"Q\" MINIPORT models have a smaller feature set than the MINIPORT-15 and MINIPORT-20.  The MP-15Q and MP-20Q have no internal power supply; a maintained 10-30VDC supply capable of supplying 10 mA is required to turn on the outlets.  This can be supplied by a Furman PowerLink, ASD-120 or PS-8R (with a simple internal modification to the PS-8R).  UL, C-UL pending.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449273020519,"sku":"5750","price":159.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_mp20.jpg?v=1787088391"},{"product_id":"furman-mp-20q","title":"Furman MP-20Q","description":"\u003cp\u003eThe \u003cstrong\u003eFurman MINIPORT-20 Power Relay \u003c\/strong\u003eis a UL\/CUL listed, 20 amp, relay switched 120 VAC outlet, with a terminal strip that allows remote control via safe, inexpensive, low voltage Class 2 wiring.  Also available is the MINIPORT-15, which is functionally identical except for its 15 amp rating.  Both models include an internal 12 VDC supply, and can be controlled from a remote location with maintained or momentary contact switches.\u003c\/p\u003e\n\u003cp\u003eMultiple MINIPORTs may be connected together so that all are controlled by a single switch closure, and may be linked so that all turn on simultaneously or one by one, in a delayed sequence.  If delayed, the delay interval between the turn-on of one MINIPORT and the next is approximately three seconds.  (Delayed turn-on is useful in avoiding large inrush currents that can trip house circuit breakers, that would otherwise occur if all amps were turned on simultaneously.)  Turn-off always occurs simultaneously, however.\u003c\/p\u003e\n\u003cp\u003eA Furman PowerLink can also be used to control MINIPORT(s).  In this use, the MINIPORT(s) areconnected to terminals on the PowerLink, which provide the necessary control functions. MINIPORTs are similarly compatible with the Furman PowerPort and ASD-120 Sequenced Power Distro.  With the addition of a PS-REL AC Relay to provide control, a MINIPORT can be used to extend the capacity of any other Furman power product — or, for that matter, any product with a switched outlet, such as a receiver\/ amp controlled with a wireless remote.  When used in this manner, the MINIPORT is switched on or off when the outlet that the PS-REL is plugged into goes on or off.\u003c\/p\u003e\n\u003cp\u003eBoth the MINIPORT-15 and the MINIPORT-20 come equipped with two knockout holes for permanent installation with 1\/2\" conduit — one on the top surface, the other on the bottom.  Use of the bottom knockout hole requires removing the AC cord.  According to the National Electrical Code, 1\/2\" conduit can accommodate up to five 20 amp circuits using ten THWN 12 gauge stranded wires; however, local codes should be checked for exact requirements.\u003c\/p\u003e\n\u003cp\u003eMINIPORTs are housed in rugged steel enclosures and come equipped with a heavy duty, 10 foot AC cord.  The MINIPORT-15 is fused; the MINIPORT-20 is equipped with a precision magnetic circuit breaker.  The MINIPORT-20 and MINIPORT-15 are UL and CUL (Canadian) listed.  Note: Because of its UL listed 20 amp rating, the MINIPORT-20 uses a 20 amp AC plug with perpendicular (not parallel) blades.  If in doubt regarding your installation, please consult an electrician or call the factory. The MINIPORT-20 is an upgrade of an earlier Furman MINIPORT.  The primary differences are the ability to use momentary switches, the delayed turn-on option, and the additional knockout holes.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan class=\"bold_text\"\u003eDimensions:\u003c\/span\u003e \u003c\/strong\u003e5.5\" (H) x 3.75\" (W) x 2\" (D). With mounting bracket, width is 5.25\".\u003c\/p\u003e\n\u003cp\u003eThe MINIPORT-15Q (15amp) and the MINIPORT-20Q (20amp) provide a pair of remotely activated, relay-controlled outlets which are both set up for mounting in any standard electrical Quad Box, either directly or with a \"mud ring\" attached.\u003c\/p\u003e\n\u003cp\u003eDue to the space limitations of a Quad Box, the \"Q\" MINIPORT models have a smaller feature set than the MINIPORT-15 and MINIPORT-20. The MP-15Q and MP-20Q have no internal power supply; a maintained 10-30VDC supply capable of supplying 10 mA is required to turn on the outlets.  This can be supplied by a Furman PowerLink, ASD-120 or PS-8R (with a simple internal modification to the PS-8R). UL, C-UL pending.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449273086055,"sku":"5753","price":99.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_mp20q.jpg?v=1787088392"},{"product_id":"furman-cn-2400s","title":"Furman CN-2400S Bidirectional Sequencer","description":"\u003cp\u003eDesigned for Commercial A\/V Installers, the \u003cstrong\u003eCN-2400S\u003c\/strong\u003e combines robust control capabilities via SmartSequencing™ Technology, advanced AC protection, AC noise filtration, and optional compatibility with the BlueBOLT® Remote Power and Energy Management Platform (BB-RS232 adaptor required, sold separately).\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThe new CN-2400S is one of the first products to feature Furman’s SmartSequencing™ technology, which allows large and complex A\/V systems to be safely powered on and off with a simple press of a button or turn of a key, even by nontechnical personnel. SmartSequencing’s bidirectional communications between installed units enables a primary unit to control and sequence multiple secondary units, ensuring multizone electronic systems are powered on and off safely and dependably from a single control point across an entire installation. Units can be connected via current loop at runs of more than 1,000 feet with backwards compatibility with Furman’s legacy sequencers.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eIn addition, the CN-2400S offers robust control options, equipped with RS-232 ports and command sets for integration with control systems. An optional RS-232-to-Ethernet adaptor (sold separately) adds full IP-addressability to the unit, allowing it to be controlled, programmed, and monitored from a smartphone, tablet, PC, or any Web-enabled device via Telnet, direct HTTP connection, or Panamax\/Furman’s BlueBOLT®-hosted remote power and energy management platform.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC Voltage Input Range:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e90-139VAC, 50\/60Hz \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaximum AC Current Rating:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e20 amps (Thermal breaker) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC Cord:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e3\/12AWG, 10 feet, black, fixed, NEMA 5-15P plug \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC Receptacles:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRear Panel Outlets: 2 Unswitched NEMA 5 20R’s (1 duplex), 6 Sequenced NEMA 5-20R’s (3 duplexes each controlled by separate relay) \u003c\/li\u003e\n\u003cli\u003e Front Panel: One NEMA 5-15R Convenience Outlet, Unswitched \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSurge\/Under-Overvoltage Protection: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e AC Surge Protection: SMP \u003c\/li\u003e\n\u003cli\u003eSpike Protection Mode: Line to neutral, zero ground leakage \u003c\/li\u003e\n\u003cli\u003e Spike Clamping Voltage: 188VAC peak @ 6,000 volts\/3,000 amps \u003c\/li\u003e\n\u003cli\u003e Response Time: 1 nanosecond \u003c\/li\u003e\n\u003cli\u003eMaximum Surge Current: 6,500 Amps \u003c\/li\u003e\n\u003cli\u003eAC Undervoltage Protection: EVS, 77VAC+\/-3VAC \u003c\/li\u003e\n\u003cli\u003eAC Overvoltage Protection: EVS, 145VAC+\/-5VAC \u003c\/li\u003e\n\u003cli\u003eAC Overvoltage Reset Modes: Manual and Auto-reset (configurable) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC Filtering\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLiFT \u003c\/li\u003e\n\u003cli\u003eNoise Attenuation: Linear, 10dB @10KHz, 40dB@100KHz, 50dB@500KHz \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating Temperature Range: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e 5C (40F) to 40C (105F) degrees \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHumidity Range: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u0026lt;90% rH (Relative Humidity) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eUser Interface: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eKeyswitch: Front panel, 3-position keyswitch (On, Off, Remote) \u003c\/li\u003e\n\u003cli\u003eKeys: Included, 1 pair \u003c\/li\u003e\n\u003cli\u003ePushbutton Switch: Front panel, hidden by security cover \u003c\/li\u003e\n\u003cli\u003eCircuit Breaker: Front panel, pushbutton, 20A Thermal Breaker \u003c\/li\u003e\n\u003cli\u003eFront panel diagnostic indicators: Primary link, Secondary link, Ethernet, Remote off, Delay 1, Delay 2, Delay 3, Power, Protection OK, Extreme Voltage \u003c\/li\u003e\n\u003cli\u003eFront Panel DIP Switches: Front panel. Hidden by security cover, 1 Minute Delay, 2 Minute Delay, 4 Minute Delay, Force Off NO\/NC, 12V Mode On\/Off BND Mode On, Momentary\/Maintained, Primary\/Secondary, EVS Reset Auto\/Manual \u003c\/li\u003e\n\u003cli\u003ePotentiometer: Front panel, hidden by security cover, fine tune delay adjust \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eControl\/Status\/Triggering (Rear Panel): \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e Remote Terminal: +5-30VDC In, 12VDC (12mA) Out \u003c\/li\u003e\n\u003cli\u003eSmartSequencing: Phoenix 4-Pin Connector, Screw Terminals, Primary \u0026amp; Secondary Links (Current Loop - 1000’ nominal) \u003c\/li\u003e\n\u003cli\u003eRemote Terminal: Phoenix 4-Pin Connector With Screw Terminals; +12V, STAT, REM, GND (Class 2 Wiring) \u003c\/li\u003e\n\u003cli\u003eForce Off\/Delay 3 Terminal: Phoenix 5-Pin Connector With Screw Terminals, FORCE OFF, DELAY 3 (Class 2 Wiring) \u003c\/li\u003e\n\u003cli\u003eRS-232 Compatible: Yes, DB-9 Connector \u003c\/li\u003e\n\u003cli\u003eIP Addressability: Optional, via BB-RS232 Ethernet\/RS-232 Adaptor (sold separately) for IP control via Telnet, HTTP, BlueBOLT® \u003c\/li\u003e\n\u003cli\u003eVoltmeter: Available with RS-232\/Ethernet option, ± 2VAC accuracy \u003c\/li\u003e\n\u003cli\u003eAmmeter: Available with RS-232\/Ethernet option, ±1A accuracy \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower Consumption (No Load): \u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e10 Watts \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44449543913575,"sku":"33029","price":871.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman_cn2400s_front2_2d1bb77a-b245-451d-9574-59645ced5224.jpg?v=1787089391"},{"product_id":"furman-d10-pfp-power-distributor","title":"Furman D10-PFP Power Distributor","description":"\u003cp\u003eThe \u003cstrong\u003eFurman D10-PFP Power Distributor\u003c\/strong\u003e is a sturdy, rack-mountable power distributor. Featuring 10 rear panel outlets with circuit breaker, it offers a convenient way to power a rack full of equipment up to a 15 amp load. The sturdy, all steel construction and heavy-duty 6 foot (14 AWG) three conductor cord provide ultimate durability and longevity. Note that the D10-PFP is a power distributor only, and offers no surge protection or conditioning functions, making it an ideal extension to an existing branch circuit.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44450457518183,"sku":"107373","price":68.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman-d10-pfp_107373_1_3804bd90-9ac6-4cf3-8353-eddf428b00fa.jpg?v=1787093138"},{"product_id":"furman-sound-cn-15mp-contractor-series-15a-miniport","title":"Furman Sound CN-15MP Contractor Series 15A MiniPort","description":"\u003cp\u003eThe \u003cstrong\u003eFurman Sound CN-15MP Contractor Series 15A MiniPort\u003c\/strong\u003e delivers SmartSequencing outside of the equipment rack, with remote relay.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFurman’s Contractor Series MiniPorts extend the benefits of SmartSequencing to electronics outside of the equipment rack, providing tremendous flexibility to any installation scenario. Units may be daisy-chained and fully controlled via a Furman SmartSequencer, legacy Furman sequencer, third-party sequencers, via the Internet (with BB-RS232 adaptor and SmartSequencer), and\/or control and automation systems.\u003c\/p\u003e\r\n\r\n\u003cp\u003eDIP switches and potentiometer allows customization of settings such as sequencing delays, 12V on\/off, and more. Security covers are provided to prevent unauthorized personnel from tampering with DIP switches.\u003c\/p\u003e\r\n\r\n\u003cp\u003eSequencing of duplex initiated remotely by standard analog triggering (remote terminal) or digital link (SmartSequencing from CN-1800S or CN-2400S).\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe CN-15MP can shut itself off automatically when triggered by a fire alarm.\u003c\/p\u003e","brand":"Furman","offers":[{"title":"Default Title","offer_id":44450513748071,"sku":"100789","price":327.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0658\/8848\/5479\/files\/furman-cn-15mp-15a-miniport_100789_1_692e667e-07fd-4e75-aca4-d5ac402333c1.jpg?v=1787093368"}],"url":"https:\/\/vintageking1.myshopify.com\/collections\/tools-accessories-recording-accessories-electrical-power-sequencers-relays.oembed","provider":"VINTAGE KING AUDIO","version":"1.0","type":"link"}